Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation Instructions
Adjustable Glass Shelf Kit
0132-524-GL2
Tools Required (not included):
- Power Drill
- 1/16" Drill Bit or 3/16" Drill Bit
- Level
- Tape Measure
- #2 Phillips Bit
- Phillips Screwdriver
- Pencil
Installation Materials (included):
- (2) Shelves
- (4) Decorative Finial
- (4) Shelf Clamp
- (2) 18" Wall Standard
- Mounting Hardware
Load Rating:
- 50 lbs when mounted into studs
Installation:
Step 1: Select a location to install the shelf kit. Mark the location of the top screw hole of
the left standard with a pencil.
NOTE: For proper installation the slots located on the standards must always be facing
the left. Both standards are identical.
Step 2: Mark the location of the top screw hole of the right standard 16" to the right of the
first mark. Use a level to ensure the standards will be the same height Figure 1.
NOTE: If the standards are not being installed directly into a stud, pre-drill an anchor
hole using a 3/16" drill bit in the locations marked above. Then insert the anchors
and continue.
NOTE: If the standards are being installed directly into a stud, pre-drill a screw hole
using a 1/16" drill bit in the locations marked above and continue.
Step 3: Check to ensure the slots on the standards are facing towards the left, then fasten
the top screw through each standard using the screws provided.
Step 4: Use a level to ensure that the standards are straight up and down. Then use a
pencil to mark the location of the bottom screw hole on each standard, making sure
marks are 16" apart.
Step 5: Carefully move the bottom of the standards to the side and pre-drill the
appropriate holes Figure 2.
NOTE: If the standards are not being installed directly into a stud, pre-drill an anchor
hole using a 3/16" drill bit in the locations marked above. Then insert the anchors
and continue.
NOTE: If the standards are being installed directly into a stud, pre-drill a screw hole
using a 1/16" drill bit in the locations marked above and continue.
Step 6: Carefully move the standards back to the straight up and down position. Then
fasten the standards to the wall using the screws provided.
Slots to
Slots to
the left
the left
16"
Top
Level
screw hole
Figure 1
Slots to
Slots to
the left
the left
Pre-Drill Hole
Figure 2
Publicidad
Manuales relacionados para SHELF-MADE 0132-524-GL2
Resumen de contenidos para SHELF-MADE 0132-524-GL2
- Página 1 Installation Instructions Adjustable Glass Shelf Kit 0132-524-GL2 Installation: Step 1: Select a location to install the shelf kit. Mark the location of the top screw hole of the left standard with a pencil. NOTE: For proper installation the slots located on the standards must always be facing the left.
- Página 2 Installation Instructions (continued) Adjustable Glass Shelf Kit 0132-524-GL2 Installation: Caution: - Do not overtighten screws as they Step 7: Place each finial in the top and bottom ends of each standard Figure 3. may cause stripping and result in NOTE: If the finials don’t fit loosen the screws, insert the finials, and re-tighten loss of shelf integrity the screws.
- Página 3 Instructions d’installation Ensemble d’ é tagères en verre réglables 0132-524-GL2 Installation: Étape 1: Choisissez l’endroit où vous installerez l’ensemble d’étagère. Marquez au crayon l’emplacement du trou supérieur du montant de gauche. REMARQUE: Pour une installation adéquate, les fentes situées sur les montants doivent toujours être orientées vers la gauche.
- Página 4 Instructions d’installation (continue) Ensemble d’ é tagères en verre réglables 0132-524-GL2 Attention : Installation: - Ne serrez pas excessivement les vis; Étape 7: Insérez les embouts aux extrémités supérieures et inférieures de chaque montant, ceci pourrait les fausser et compromettre tel qu’illustré...
-
Página 5: Instalación
Instrucciones de instalación Kit de estanterías de vidrio ajustables 0132-524-GL2 Instalación: Paso 1: Seleccione una ubicación para instalar el equipo de estante. Con un lapiz, marque la ubicación del orificio del tornillo superior del riel izquierdo. NOTA: Para lograr una instalación adecuada, las ranuras ubicadas en los rieles siempre deben quedar mirando a la izquierda. - Página 6 Instrucciones de instalación (continuación) Kit de estanterías de vidrio ajustables 0132-524-GL2 Instalación: Precaución: - No ajuste demasiado los tornillos ya que Paso 7: Ubique cada tope en las terminaciones superiores e inferiores de cada riel. Figura 3. puede provocar un decapado y dar lugar NOTA: Si los topes no encajan, afloje los tornillos, inserte los topes y vuelva a a la pérdida de la integridad del estante...