Read the instructions before connecting the device and store them in a safe place for
reference.
DO NOT DRINK WATER FROM THE HAND WASHBASIN. THIS DEVICE
IS NOT DESIGNED FOR DRINKING WATER.
This hand washbasin cannot replace any items that require hot and cold
running water at the facilities in accordance with the applicable laws
CONTENTS & AVAILABLE SPARES
Casing for portable, self-contained basin. (spare not available)
060610 - Detachable transom for attachment to portable basin.
080418 - 1 box dispenser of gloves, tissue or towels.
460236 - Electronic soap dispenser (uses batteries).
461008 - Turning tap 140x200x1/2" (50mm nut).
454260 - Flexible drainage pipe for self-contained basin.
461430 - Stackable translucent 10 l tank for dirty water
461428 - Translucent 10 l tank for clean water
454202 - 2 ½" Valve with trough for 500mm sink.
421002 - M4x16-mm metric thread hex head screw.
421050 - Hexagon nut metric thread M4.
421004 - M5x8-mm metric thread hex head screw.
421052 - M5 metric thread hex nut.
409822 - Plastic nylon Fisher 6X30mm peg.
421038 - Plate thread bolt 22x4,8mm. DIN 7981 A2.
Other spares:
460412 Hydraulic pedal high fl ow
485020 - 50x18-mm.ø plastic wheel for self-contained basin.
461432 - "Not drinking water" vinyl adhesive for tank.
ASSEMBLY
Check the contents.
When assembling, it is advisable to use special gloves in order to avoid any bad cut on hands.
Pull out front door and remove the plastics from doors and washbasin.
Insert the backsplash sliding it along the rails and secure it to the back of the basin using the nuts
and screws.
Remove the front part of the soap dispenser using the key provided.
Attach the soap dispenser to the backsplash using the nuts and screws.
Introduce four AA batteries into the battery compartment · Fig. 1
Fill the soap container and replace the front part of the soap dispenser.
Secure the tissue dispenser using nuts and screws.
Insert the spout in the upper orifi ce and fi x it with the provided bolts · Fig. 2
Assemble the drain valve · Fig. 3
Connect to the spout the closest hose.
Insert the tank with the label of non-drinking water under the spout.
Connect the fl e xible drain pipe to the valve making a Ubend and attach the other end to the dirty
water tank · Fig. 4
Remove the small plug from the clean water tank and insert the remaining hose through this hole.
Make sure that it runs under the handle Fig 5
USE
When using it for the fi rst time, step down and release the button all the way repeatedly until the
water comes out.
Then step down and release repeatedly.
SAFETY, CLEANING AND STERILIZATION
DO NOT DRINK WATER FROM THE HAND WASHBASIN. THIS DEVICE IS NOT DESIGNED
FOR DRINKING WATER.
This hand washbasin cannot replace any items that require hot and cold running water at the facili-
ties in accordance with the applicable laws.
CLEANING AND STERILIZATION
• Wash both tanks with plenty of drinking water.
• Sterilize before the fi rst use of each day, by adding a sterilizing product approved for drinking
water according to the instructions of the manufacturer. Feed all the circuit with the water and the
sterilizing product stepping on the button until the tank is empty.
• Then fi ll the tank with drinking water. It is now ready for use.
• Perform this procedure before the start of each day.
SAFETY
• Empty the tank of used water at least once an hour or when is full.
• Empty the tank of drinking water at least once every 6 hours.
• When the device is not being used for a long period of time, empty the tanks, wash them and store
them completely dry.
• Store the containers clean and dry in a dark, dry and healthy area.
• Replace the tanks every six months
• In order to avoid cross-contamination, do not use the bin.
MAINTENANCE OF STAINLESS STEEL
• Use only water and neutral soap when cleaning.
• Wipe with a soft cloth.
• Rinse with plenty of drinking water.
• Dry with a soft cloth.
• Do not use acids or strong detergents and do not rub with a scourer or spatula.
WARRANTY
This device has two years of warranty. An improper use void the warranty of the unit.