Tabla de contenido
Publicidad
Cordless Impact Wrenches
Declarations
EU DECLARATION OF CONFORMITY
We, CHICAGO PNEUMATIC Tool Co.LLC, 1815 Club-
house Road, Rock Hill, SC 29730 - USA, declare under our
sole responsibility that the product (with name, type and se-
rial number, see front page) is in conformity with the follow-
ing Directive(s):
2006/42/EC, 2014/30/EU, 2011/65/EU
Harmonized standards applied:
EN 62841-2-2:2015 + AC1:2015, EN 61000-6-3 : 2007 +
A1 : 2011, EN 61000-6-2 : 2005, EN 62479:2010
Authorities can request relevant technical information from:
Pascal Roussy, R&D Manager, Ets Georges Renault, 38 rue
Bobby Sands, BP10273 44818 Saint Herblain, France
Saint-Herblain, 15/04/2021
Pascal ROUSSY
Signature of issuer
Noise and Vibration Declaration Statement
• Sound pressure level 87 dB(A) , uncertainty 3 dB(A), in
accordance with EN62841.
• Sound power level 98 dB(A) , uncertainty 3 dB(A), in
accordance with EN62841.
• Vibration total value 9,3 m/s
accordance with EN62841.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We, CHICAGO PNEUMATIC Tool Co.LLC, cannot be
held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
2
2
, uncertainty 3,1 m/s
http://
and selecting 'Tools' then 'Legis-
© Chicago Pneumatic - 8940176366
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
Regional Requirements
WARNING
This product can expose you to chemicals including
lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For
more information go to
https://www.p65warnings.ca.gov/
FCC compliance Class B
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user's authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this de-
vice must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Responsible party:
Name: Mark Johnson
Position: General Manager
Address: Chicago Pneumatic Tool Company
LLC 1815 Clubhouse Road Rock Hill
, in
SC 29730
USA
Mobile: +1 800 624 4735
Email: mark.johnson@desouttertools.com
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gener-
ates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference
will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
▪ Reorient or relocate the receiving antenna.
▪ Increase the separation between the equipment and re-
ceiver.
▪ Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
▪ Consult the dealer or an experienced radio/TV techni-
cian for help.
Safety Information
7
Publicidad
Tabla de contenido
