Bandsaw; Technical Data; Machine Description; General Notes - Scheppach 1901506901 Traducción De Manual De Instrucciones Original

Bandsaw

Sawband 20 mm
Fence
Suction connectio piece, 100 mm diam
Push stick
Assembly Accesoires
Operating instructions
Length/width/height mm ............................................................................. .......................2060x1050x1150
Bench size mm ............................................................................................................................... 840x640
Working height mm ................................................................................................................................. 900
Sawband mm ......................................................................................................................... 20x0,45x4425
Band wheel diameter mm ....................................................................................................................... 600
Cutting height at 90° mm ........................................................................................................................ 400
Clearance width mm .............................................................................................................................. 590
Parallel cutting width mm ....................................................................................................................... 300
Parallel stop length mm .......................................................................................................................... 650
Bench swing range mm ................................................................................................... degrees -15°/+47°
Cutting speed with 2 switching levels m/min ....................................................................................... 1200
Weight kg ................................................................................................................................................ 250
Motor
Consumption P1 (kW)
Output P2 (kW)
Noise parameters
The noise emission values determined ac-
cording to EN 23746 for the sound level and
according to EN 31202 (coefficient of correction
k3 calculated according to Appendix A.2 of EN
31204) for the sound level at the workplace are
as follows, based on the working conditions
D GB
listed in ISO 7904 Appendix A:
Due to its perfected design, the machine offers
a versatile application for processing wood and
plastics in the workshop.
The upper and lower bandwheel is protected
by a fixed guard and an articulated cover. Upon
opening the cover, the machine is switched off.
Switching on again is only possible with the co-
ver closed. The non-cutting part of the sawbelt
above the table top is covered by a guard fixed
1. After unpacking, check all parts for any trans-
port damage. Inform the supplier immediately
of any faults.
2. Later complaints cannot be considered.
3. Make sure the delivery is complete.
4. Before putting into operation, familiarize your-
self with the machine by carefully reading these
instructions.
5. Use only original scheppach accessories,
wearing or replacement parts. You can find
replacement parts at your scheppach dealer.
6. When ordering, include our item number
and the type and year of construction of the
machine.
NOTE:
In accordance with valid product liability laws,
the manufacturer of this device shall not be
responsible for damage to and from this device
which results from:
1. Improper care.
2. Noncompliance with the Operating Instruc
Supply volume

Technical data

230 V / 50 Hz
2,80
2,00
Sound level at the workplace in dB
Idle running LpAeq =85 dB(A)
Operation LpAeq = 95 dB(A)
A measurement uncertainty allowance K = 4 dB
applies to the mentioned emission values.

Machine description

to the sawbelt guide, the latter being protected
against inadvertant opening by the fixed guard
of the upper band wheel. The non-cutting part of
the sawbelt under the table top is protected by a
fixed cover.
The swivelling range of the table from -15° to
+47°
allows versatile cutting possibilities (e.g)

General notes

tions.
3. Repairs made by unauthorized persons.
4. The installation and use of any parts which
are not original scheppach replacement parts.
5. Improper use and application.
6. Failure the electrical system as a result of
non com pliance with the legal and applicable
electrical directives and VDE regulations
0100, DIN 57113 / VDE 0113.
 We recommend that you read through the
entire operating instructions before putting
into operation.
These operating instructions are to assist you
in getting to know your machine and utilize its
proper applications.
The operating instructions contain important
notes on how you work with the machine safely,
expertly, and economically, and how you can
avoid hazards, save repair costs, reduce down-
time and increase the reliability and service life
14
400 V / 50 Hz
3,80
2,90
• Longitudinal cuts
• Crosscuts
• Diagonal cuts
• Curved and irregular cuts
• Cuts for dovetails and tenons
• On-edge cuts of squared beams
Please consult also the working hints in the
operating instructions
of the machine.
In addition to the safety requirements contained
in these operating instructions, you must be
careful to observe your country's applicable
regulations.
The operating instructions must always be near
the machine. Put them in a plastic folder to
protect them from dirt and humidity. They must
be read by every operator before beginning work
and observed conscientiously. Only persons
who have been trained in the use of the machine
and have been informed of the various dangers
may work with the machine. The required mini-
mum age must be observed.
In addition to the safety requirements contai-
ned in these operating instructions and your
country's applicable re gulations, you should
observe the generally recognized technical
rules concerning the operation of woodworking
machines.