Filling The Water Tank; Operation; Switching The Appliance On; Turning The Appliance Off - Parkside PDR 12 A1 Traducción Del Manual De Instrucciones Original

♦ Disconnect the mains adapter
charging socket of the mains adapter
charged.
♦ Replace the charging socket cover

Filling the water tank

towards the Open mark until you can pull the
♦ Turn the water tank
water tank off the base
create suitable counter-pressure.
♦ Open the lid of the water tank
with water. Do not fill the tank beyond the 5 l mark.
NOTE
► The water tank has a capacity of 5 litres.
► Fill the water tank with fresh water only.
► Do not open the lid during operation.
♦ Close the lid of the water tank
♦ Put the water tank back on the base
towards the Close mark on the base
Hold the base firmly with one hand to create suitable counter-pressure.
Ensure that the I mark on the base
water tank when it has clicked into place.

Operation

Switching the appliance on

CAUTION!
► If the pump runs for 2 minutes without drawing in liquid, it will run dry
and the appliance will be damaged.
♦ Press the On/Off switch to switch the appliance on. The status
LED lights up green. The pump builds up pressure.
Turning the appliance off
♦ Press the On/Off switch again to switch the appliance off.
The status LED goes out.

Using the hand sprayer

♦ Remove the hand sprayer
♦ Point the hand sprayer at the surface you wish to clean.
♦ Pull the trigger on the hand sprayer
continuous low-pressure jet.
♦ Release the trigger to stop the low-pressure jet and stop cleaning.
NOTE
► When the battery is empty, the status LED
appliance switches itself off.
► If you do not activate the trigger
ance switches itself off.
│ GB │ MT
■ 30
from the mains power outlet and the
5a as soon as the battery is fully
to close the charging socket.
. Hold the base firmly with one hand to
. Use a tap to fill the water tank
.
. Turn the water tank
until it clicks into place.
is aligned with the I mark on the
from its bracket on the base .
and keep it held in for a
flashes red and the
for around 5 minutes, the appli-

Stopping operation

♦ Remove the water tank as described in the section "Filling the water
tank" and empty it. Replace the water tank on the base.
♦ Pull in the trigger of the hand sprayer
the sprayer.
♦ Press the On/Off switch to switch the appliance off.
♦ Return the hand sprayer to its bracket on the base
CAUTION!
► If you do not completely empty the appliance, it could be susceptible
to frost damage.

Maintenance

RISK OF ELECTRIC SHOCK!
► Switch off the appliance before carrying out any cleaning or mainte-
nance work or exchanging components.
► Do not clean the appliance while charging it.
► Disconnect the appliance from the power supply if necessary.
♦ Clean the appliance with a damp cloth.

Replacing the fuse in the 12 V connector plug

To protect the on-board power supply of your vehicle, there is a fuse in the
12 V car adapter . If the appliance stops working, check the fuse and
10a
replace it if necessary.
♦ Open the 12 V connector plug
insert anticlockwise (using pliers if necessary) and removing it.
♦ Remove the plug tip from the fuse and take out the fuse.
♦ Insert new 10 A fuse into your 12 V charger adapter
♦ Fit the plug tip to the slightly protruding end of the fuse and screw
the previously removed screw insert back in.

Storage

♦ Store the appliance in a clean, level and dry location at a temperature
between 0°C and 40°C.

Disposal

The packaging is made from environmentally friendly material
and can be disposed of at your local recycling plant.
Do not dispose of power tools in your normal
household waste!
until no more water exits
.
by carefully unscrewing the screw
10a
.
10a
PDR 12 A1