Black+Decker ASD14 Traducción De Las Instrucciones Originales página 6

ENGLISH
Lock the tool by setting the forward/reverse slider (2) to
u
the centre position.
Open the single sleeve chuck (6) by turning it.
u
Insert the bit shaft into the chuck and firmly tighten the
u
single sleeve chuck.
This tool is supplied with a screwdriver bit in the bit holder (7).
To remove the screwdriver bit from the bit holder, lift the bit
u
from the recess.
To store the screwdriver bit, firmly push it into the holder.
u
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the single sleeve chuck and turning
the tool on. Damage to the single sleeve chuck and personal
injury may occur when changing accessories.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
To charge the battery (9), insert it into the charger (10).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (11) will blink.
The charge is complete when the charging indicator (11)
switches to continuously on. The charger and the battery can
be left connected indefinitely. The LED will switch on as the
charger occasionally tops up the battery charge.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
6
(Original instructions)
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (11) will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (9).
u
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
u
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
To lock the tool, set the forward/reverse slider into the
u
centre position.
Switching on and off
Select forward or reverse rotation using the forward/
u
reverse slider (2).
To switch the tool on, press the switch (1). The tool speed
u
depends on how far you press the trigger switch.
To switch the tool off, release the trigger switch.
u
Autoselect technology (fig. D)
TM
For drilling in wood, metal and plastics, press the drill
u
mode selector button (3).
For screwdriving, press the screwdriver mode selector
u
button (4).
Autosense technology
TM
In screwdrive mode, this tool is equipped with Autosense
technology that helps drive screws accurately and without
effort.
Select Screwdrive mode & ensure the forward/reverse (2)
u
is pushed to the left.
Pull the trigger switch (1) to drive a screw into the
u
workpiece and the tool will automatically stop when the
screw is flush to the workpiece.
TM