DeWalt D26200 Traducido De Las Instrucciones Originales página 38

EnGLIsH
The knurled knob 29 at the bottom end of the depth
adjustment rod can be used to make minor adjustments.
1. To decrease the cutting depth, rotate the knob clockwise
(looking down from the top of the router).
2. To increase the cutting depth, rotate the knob
counterclockwise (looking down from the top of the router).
nOTE: One complete rotation of the knob results in a change of
about 1 mm in depth.
Cutting with the Plunge Base (Fig. K)

WARNING: To reduce the risk of injury, turn unit
off and disconnect it from power source before
installing and removing accessories, before
adjusting or when making repairs. An accidental start-
up can cause injury.
nOTE: The depth of cut is locked in the plunge base's default
state. The plunge lock requires user actuation to enable the
"release to lock" plunge mechanism.
1. Depress the plunge lock lever
down until the cutter reaches the set depth.
2. Release the plunge lock lever
is reached.
nOTE: Releasing the plunge lock lever automatically locks
the motor in place.
nOTE: If additional resistence is needed use the hand to
depress the plunge lock lever.
nOTE: If additional clamping strength is required, press the
lock lever further to tighten in the clockwise direction.
3. Perform the cut.
4. Depressing the plunge lock lever will disable the locking
mechanism allowing the router cutter to disengage from
the work piece.
5. Turn the router off.
Operation: All Bases
Direction of Feed (Fig. L)
The direction of feed is very important when routing and can
make the difference between a successful job and a ruined
project. The figures show the proper direction of feed for some
typical cuts. A general rule to follow is to move the router in a
counterclockwise direction on an outside cut and a clockwise
direction on an inside cut.
Shape the outside edge of a piece of stock by following
these steps:
1. Shape the end grain, left to right
2. Shape the straight grain side moving left to right
3. Cut the other end grain side
4. Finish the remaining straight grain edge
Choosing Router Speed (Fig. A)
Refer to the speed selection Chart to choose a router speed.
Turn the variable speed dial 3
Soft Start Feature
The compact routers are equipped with electronics to provide a
soft start feature that minimizes the start up torque of the motor.
36
16 and plunge the router
16 when desired depth
to control router speed.
Variable Speed Control (Fig. A)
This router is equipped with a variable speed dial
infinite number of speeds between 16000 and 27000 RPM.
Adjust the speed by turning the variable speed dial
NOTICE: In low and medium speed operation, the speed
control prevents the motor speed from decreasing. If you
expect to hear a speed change and continue to load the
motor, you could damage the motor by overheating.
Reduce the depth of cut and/or slow the feed rate to
prevent tool damage.
The compact routers are equipped with electronics to monitor
and maintain the speed of the tool while cutting.
SPEED SELECTION CHART
DIaL aPPROX.
sETTInG RPM
1 16000
2 18200
3 20400
4 22600
5 24800
6 27000
nOTE: Make several light passes instead of one heavy pass for
better quality work.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Brush Inspection
For your continued safety and electrical protection, brush
inspection and replacement on this tool should ONLY be
performed by a D WALT factory service center, a D
e
authorized service center or other qualified service personnel.
At approximately 100 hours of use, take or send your tool to your
nearest D WALT factory service center or D
e
service center to be thoroughly cleaned and inspected. Have
worn parts replaced and lubricated with fresh lubricant. Have
new brushes installed, and test the tool for performance.
Any loss of power before the above maintenance check may
indicate the need for immediate servicing of your tool. DO NOT
CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper
operating voltage is present, return your tool to the service
station for immediate service.
3 with an
3 .
aPPLICaTIOn
Large diameter cutters
Small diameter cutters.
Softwoods,plastics, laminates.
WALT
e
WALT authorized
e