Stagnoli SATURNO-S Manual De Usuario página 19

In this section you will find information about the firmware version. When accessing the interface, allow the firmware
"Stagnoli" logo to be visible before changing sections so that there are no slowdowns or malfunctions associated with
The first box displayed shows the status of the traffic lights in real time and allows the entire system to be kept under
The seventh column, which only appears if the "Booking" or " Combined" operating mode is active, indicates whether a
Only if a parking logic has been set another column called " Free places " will be displayed, which will indicate the number
of free places left within the area managed by that particular traffic light. From there you can also enter the number of free
The second box displays the total cycle time of the system, which is the sum of the seconds of green and the seconds of red,
and its progressive increase in real time. Next to this box, the emergency status (white = no emergency; red = emergency)
and the stand-by status (green = no stand-by; red = system in stand-by) are indicated.
In the " Setup" section, first of all a box appears in which you are asked to add all the traffic lights used in the system, which correspond
slaves installed, using the appropriate " add " button. After adding all the traffic lights (called "Light X" by default) it will be possible to
configure each individual traffic light by using the three buttons located in the last column to the right of each row.
FIRST BUTTON: MODIFY
The first button is the "Modify" button. This allows you to:
• set the precise second in which the cycle of the traffic light considered will be started (Start);
• set the duration in seconds of the green, yellow and red light.
In order to have a correct configuration and depending on the type of operation you want, the seconds set
(start, green, yellow and red) must be added together to obtain the total operating time of that given traffic ligh
SECOND BUTTON: SETUP
By clicking on the "Setup" button you can:
• change the name of the traffic light;
• provide the control unit with the number of lamps (2 or 3);
• set the output mode (the way in which the auxiliary output should behave by choosing from the settings listed);
• set the TmAux, time expressed in seconds indicating the duration of the impulse function of the auxiliary output;
• indicate the modbus address, assigned by default, but modifiable, which is used to specify on which slave the settings should be
made;
• activate "Green stand-by", which is used to turn on the green light when the installation goes into stand-by mode;
• activate "Green emergency", which is used to turn on the green light when the system goes into an emergency state;
• activate NC input 1, NC input 2, NC input 3, which are used to ensure that the inputs have a normally closed signal (N.C.)
because by default they are set to a normally open signal (N.O.);
• indicate the number of spots in each area (only when you are in "Parking" operating mode and if you manage more than one
area otherwise leave the value set to "0").
THIRD BUTTON: REMOVE
This button allows you to delete the entire line related to a traffic light.
On the next box, instead, you can:
• choose whether to activate the possibility of overlapping greens (without this active function, it is not possible to have two green
lights at the same time for safety reasons);
STAGNOLI T.G. S.r.l., in quanto produttore, non è imputabile di alcuna responsabilità in caso di danni a cose o
persone, in quanto la programmazione è di responsabilità dell'installatore che DEVE avere tutte le competenze e
deve aver analizzato a fondo l'impianto in modo da adottare le soluzioni più sicure per gli utilizzatori.
• set the operating mode*;
• set the pre-flashing, which consists of flashing the lights before they start the cycle (expressed in seconds);
• set the area clearance time, additional time (expressed in seconds) that can be added to increase the safety factor;
• determine the response of the lights in their stand-by status;
• determine the response of the lights in an emergency status;
• indicate the number of global spots (only when you are in "Parking" operating mode and if you only manage one area; otherwise leave
the value
set to "0").
MACHINE INFORMATION SECTION
version to be displayed and the
displaying the data.
TRAFFIC LIGHTS STATUS SECTION
The first column of the box corresponds to the modbus address.
The second column corresponds to the name of the traffic light.
The third and fourth columns correspond to the status of inputs 1 and 2.
The fifth is dedicated to emergency reporting.
The sixth is dedicated to the real-time status of the traffic light.
booking is in progress and the order that bookings follow.
spots present at the time of installation.
SETUP SECTION
customize and
control.
to all the
IT
EN
FR
ES
DE
19