Before Using The Appliance - Redmond RТ-M406-E Manual De Usuario

I. BEFORE USING THE APPLIANCE
Carefully remove the appliance and its accessories from the packaging. Dispose of all
packaging materials and promotional stickers.
Keep all warning labels, warning stickers (if any), and serial number identification label
located on the housing.
After transporting or storing at low temperatures allow the appliance to stay at room
temperature for at least 2 hours before using.
Wipe the unit with a moist cloth and allow it to cool. Clean the appliance upon the first
use to avoid off-odour.
It is recommended to warm the toaster during the first use, using maximum roasting
degree ("7"), without loading the bread slices into the toaster.
II. OPERATION
Toast roasting
1. Plug in the appliance. Put bread slices into the toaster.
Bread slices should freely fit in toaster slots.
2. Press the toast loading lever smoothly, until tight, toasts will be dropped and the
roasting process will start.
3. Adjust the desired roasting degree using roasting degree controller.
Different types of bread require different roasting degrees from "1" to "7". Upon the first
roasting of bread slices use neutral roasting degree "3" or "4".
4. Pressing CANCEL button allows to stop the running process immediately. LED
indicator goes out when the roasting process is over, toasts automatically rise.
5. Carefully remove the toasts (they are hot!) from the toaster.
Defrost function
Frozen bread can be currently used for toasts. Firstly toaster defrosts bread slices, and
then automatically switches to roasting mode.
1. Plug in the appliance.
2. Put the frozen bread slices into the toaster.
3. Press the toast loading lever smoothly, until tight, toasts will be dropped and the
process of defrost and roasting will start.
4. Press DEFROST button. Adjust the desired roasting degree using roasting degree
controller.
Toast cooking time in DEFROST mode is more than in standard roasting mode.
5. Press CANCEL button to stop the running process immediately. LED indicator goes
out when the roasting process is over, toasts automatically rise.
6. Carefully remove the toasts (they are hot!) from the toaster.
Warming function
This function allows warming up toasts that are already cooled down.
1. Plug in the appliance.
2. Put the toasts into compartments.
3. Press the toast loading lever smoothly, until tight, the warming process will start.
4. Press REHEAT button.
Toaster operation time in «Warming» mode is lesser than in standard roasting mode.
Press CANCEL button to stop the running process immediately.
CAUTION! Warming degree selection is not applicable for "Warming" mode.
III. CLEANING AND MAINTENANCE
It is recommended to clean the crumb tray after each use of the appliance. Before
cleaning the appliance ensure that it is plugged off and is completely cooled down.
Clean the appliance housing if needed. Use clean, warm water and soft cloth, do not
use abrasive pastes and dish soap.
Before repeated operation or storage completely dry all parts of the appliance. Store
the assembled appliance in a dry, ventilated place away from heating appliances and
direct sunlight.
During transportation and storage, do not expose the device to mechanical stress, that
may lead to damage of the device and/or violation of the package integrity.
Keep the device package away from water and other liquids.
IV. BEFORE CONTACTING SERVICE CENTER
Problem Possible cause
You can smell the off-odour dur-
Off-odour ing the first use, this does not
signify the appliance defect
RТ-M406-E
GBR
FRA
DEU
NLD
ITA
ESP
PRT
DNK
NOR
SWE
FIN
LTU
LVA
EST
ROU
HUN
BGR
HRV
SVK
CZE
POL
RUS
GRE
Solution
TUR
If off-odour doesn't disappear
UKR
upon further use, refer to the
section "Cleaning and mainte-
KAZ
nance"
7