Led Lenser M17R Manual De Instrucciones página 6

7.1 Lock function
In the first position from the left (the selection ring has been turned to the right till it comes to a stop), the M17R cannot be switched on, either
intentionally or unintentionally. Thus, the lock function is handy for when the M17R is transported. Also, there could be situations in which the M17R
may/should not be switched on, even unintentionally.
7.2 Light Program Low
If the switch button of the "Fast Action Switch" is in the second position of the selection ring, you can use the Light Function Low Power with its
reduced brightness. By briefly tapping and letting go, you can switch to the Light Function Power with full brightness. When you tap it again, you
can switch between the Light Programs Low Power and Power. One more switching operation, and the lamp is off.
When the M17R is off, tapping can be employed, e.g. to send signals of various length in Morse code with reduced brightness.
7.3 Light Program Action
In the third position of the selection ring, by switching or tapping, the Light Function Power (full brightness) is immediately usable. As with Light
Program Low, here too, it is possible to use tapping for sending Morse signals, but with full brightness in this case.
Upon switching, the Light Function Power is firmly set and by brief tapping, it is possible to switch between the Light Functions Power and Dim.
Upon switching to 'Dim' by tapping, if the switch button remains tapped for a longer time (prolonged tapping), the M17R starts to slowly change the
brightness between low brightness and full brightness. The lamp will extinguish for one short moment if the brightest or lowest luminosity is reached.
Upon releasing the switch, the M17R continues to glow with the current brightness level. This brightness level remains saved, i.e. remains set for
the light function Dim, when the M17R is switched off. This brightness of the light function Dim is only lost, or changes, when the Power Module (shaft
with "Safety Ytrion Cell" battery pack) is unscrewed at the head (also see the Reset function under Point 9). Of course, it also changes if specifically
changed by the user as described above.
One more switching operation, and the lamp is off.
7.4 Light Program Signal
In the fourth position, by switching or tapping, the Light Function SOS (3 short, followed by 3 long, followed again by 3 short flashes) can be invoked
immediately.
If, after a switching operation, the switch is tapped, the Light Function Blink (slow, continuous blinking) is activated. Tapping once again results in
the Light Function Signal Blink (2x blinking at short intervals)
One more switching operation, and the lamp is off.
7.5 Light Program Defence
The Light Mode Defence is the one on the extreme right on the selection ring; it can be selected by turning the selection ring completely to the left
till it comes to a stop.
Upon switching, the Light Function Strobe is set and by tapping briefly, it is possible to toggle between Strobe and Power.
One more switching operation, and the lamp is off.
Here, too, the Light Functions are revolving, like with the Light Modes 2, 3 and 4. This means, for example, with Light Program 5, that after the Light
Function Power, one more tap leads to the Light Function Defence. Thus, tapping does not take you into a dead end; there is a continuous circular
series of selected light functions.
When the M17R is glowing in one of the Light Functions (2, 3 4 or 5), it also glows after a changeover (by turning the selection ring of the "Fast
Action Switch") between these 4 Light Functions. With such a changeover, the M17R has the light function that it also had when switched on
directly (e.g. with the Light Program Signal, the Light Function SOS).
8. Emergency Mode / Emergency Light Function
When the Emergency Mode is activated, the M17R has an emergency light function. For this purpose, the mode has to be activated and the M17R
has to be connected to the charger (position light at the charger glows blue, see Point 10). In this case, the pocket torch automatically goes on
when the electric supply that is providing energy to the charger fails. If positioned meaningfully, the M17R, when it is glowing, can facilitate quickly
finding an escape route in an emergency, or the lamp can be quickly found and picked up, already on. If this function is active, the M17R glows
automatically even if the charging process is interrupted by removing the M17R. Therefore, the function can also be used when the M17R has to be
ready for immediate use.
To set the Emergency Mode, set the "Fast Action Switch" to Light Program action and tap prolonged for about 10 seconds. The M17R glows
for these 10 seconds and then blinks. After blinking, the light turns off. When it flashes 4 times, Emergency Mode is activated; if it flashes twice,
Emergency Mode is disabled. If this procedure is carried out again, the setting toggles between activated and disabled and signals this by a
corresponding blinking.
9. Reset function
If the Power Module (shaft with "Safety Ytrion Cell" battery pack) is unscrewed completely at the head and the two parts are screwed together again
only after a little while, you have "reset" the M17R. You have thus reset a few functions:
- As Energy Mode, Energy Saving is active (see Point 6).
- The Emergency Mode (see Point 8) is active.
- This lamp function Dim (see Point 7.3) is set to the lowermost brightness
10. Charging
The Power Module (shaft without lamp head) contains the "Safety Ytrion Cell" battery pack, the accumulator.
Charge your M17R only in a dry place.
For charging, connect the mains plug on one side to the accompanying charger (Input: 100 V to 240 V / 50 Hz to 60 Hz) and on the other side, to a
power socket. Then connect the extension cable of the charger to the cable of the magnetic charging socket, whose blue position light then starts
to glow. You can now connect the concentric charging contacts at the end of the M17R to the magnetic charging socket. When the lamp has been
correctly connected, the charging display glows red (see Point 11) and the charging starts. The Power Module (shaft with the "Safety Ytrion Cell"
battery pack) with the unscrewed lamp head can also be charged.
See the following section on the subject of the charging indicators (see Point 11) for more information.
Note – Please ensure that there is no short-circuit at the charging contacts. The charging contacts may not be touched with moist or metallic
objects.
The magnetic charging socket can also be inserted in the cylindrical part of the charger bracket, which is a part of the supplied kit, and then locked
in place by turning a couple of times in the counter-clockwise direction like a bayonet catch. The lock is released by rotating in the other direction.
The bracket can be fastened on the wall with dowels (not scope of delivery) in such a way that the blue position lamp of the magnetic charging
socket, for example, glows downwards. Please use a sufficient number (min. 4 pieces) and suitable dowels, depending on the material of the wall.
The orientation described suggests itself when you wish to use the Emergency Module / Emergency Light function (see point 8) since the M17R
glows upwards in case of a power failure. On the other side of the bracket, the M17R can be joined to the bracket with 2 rubber rollers and fixed
permanently by using the rubber gusset that is located at the level of the two rubber rollers. The latter suggests itself if there are acceleration forces
acting on the M17R. In this manner, the M17R can be fixed in the bracket inside the vehicle if the charger bracket is fixed permanently to a vehicle.
Using an optionally available car charger connection, the M17R can also be charged at the cigarette lighter and sockets in the vehicle. These
accessory units match themselves automatically to the respective input voltage (12 V to 24 V).
˚ English
04