Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch
End Plate
Figure 2
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75430F or 87004F
Wrenches: 9/16, 11/16, 3/4
Drill Bits: 3/8"
Blocks must not overlap
in Vehicle Frame
Hitch End Plate
1
Qty. (4)
Carriage Bolt - ½-13 x 1-3/4
2
Qty. (4)
Block ¼ x 1 x 3
3
Qty. (4)
Conical Toothed Washer – ½
4
Qty. (4)
Nut ½-13
NOTE: Lowering exhaust may ease installation. To lower exhaust, remove rubber hanger from hanger bracket.
1.
Install block and carriage bolt up thru rearmost slot in vehicle frame rail and down thru forward slot in frame, each side.
2.
Install block and carriage bolt up thru rearmost slot in vehicle frame rail and back down thru same rearmost slot, each side.
NOTE: Be sure block installed in steps 1 and 2 do not overlap inside frame.
3.
Raise hitch into position on carriage bolts, making sure rear face of hitch end plate contacts lip of vehicle end panel as shown in
figure 2. Install conical toothed washers and nuts, finger tight.
4.
Using 3/8" drill bit, drill thru holes in hitch end plate into lip of vehicle end panel, two places each side.
5.
Install 3/8" hex bolts, flat washers, lock washers and nuts as shown. Tighten 3/8-16 fasteners with torque wrench to 30 lb.-ft.
6.
Raise exhaust back into position if lowered prior to hitch installation.
NOTE: If additional exhaust clearance is required, bend exhaust hanger bracket, which is welded to vehicle frame,
downward.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
Pontiac Aztek- All Models
Buick Rendezvous – All Models
Fascia
Vehicle End Panel
1234
Figure 1
5
6
7
8
Tighten all ½-13 fasteners with torque wrench to 75 Lb.-Ft.
Tighten all 3/8-16 fasteners with torque wrench to 30 Lb.-Ft.
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB Max Gross Trailer Weight
350 LB Max Tongue Weight
Wiring Access Location: SUV1, SUV2
Drill holes
5678
Vehicle End Panel
Fasteners Typical
Both Sides
Vehicle Tail Pipe
Qty. (4)
Hex Bolt – 3/8-16 x 1-1/4
Qty. (4)
Flat washer – 3/8
Qty. (4)
Lock Washer – 3/8
Qty. (4)
Nut 3/8-16
75430N
Part Numbers:
75430
44538
87004
4 Places
8-30-05
Rev. A
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Towing Products 75430
Resumen de contenidos para Cequent Towing Products 75430
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75430N 8-30-05 Rev. A 2005 Cequent Towing Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75430N 8-30-05 Rev. A 2005 Cequent Towing Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Sheet 3 of 3 75430N 8-30-05 Rev. A 2005 Cequent Towing Products Form F206 Rev A 5605...