Publicidad
Idiomas disponibles
Idiomas disponibles
3) Specifications
ITEM
Cutting depth/width
Weight, with cutting blades
Dimensions without blades
No load speed N
0
Power
Electrical rating, nominal
Dust extraction vacuum hose interface
Maximum mid-span belt deflection
Blade mount bolt torque
Vibration emissions GP Blade (k=1.5)
Vibration emissions Plunge Blade (k=1.5)
Vibration emissions Switch Blade (k=1.5)
A- Weighted sound pressure level L
WA
Uncertainty KpA
A- Weighted sound power level L
WA
Uncertainty L
WA
WARNING:The declared vibration emission level
is based on measurements representing the main
applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period. An estimation of the level of
exposure to vibration should also take into account the
times when the tool is switched off or when it is running
but not actually doing the job.
This may significantly reduce the exposure level
over the total working period. Identify additional
safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of
work patterns.
WARNING: The values state here only indicates
the loudness emitted by this machine. Whether the
operator is required to wear hearing protection cannot
be determined here. This depends on how much noise
reaches the operator's ear. Even though it may not be
explicitly required, it is in your own interest to always
wear hearing protection when operating this machine.
6
4) How to Use
SPECIFICATION
120mm (4 3/4")/6.5mm (1/4")
operation the AS175 may
depending on blade
cause hand-arm vibration,
4.3kg (9.5lb)
which can result in fatigue
610 mm (24") L
or discomfort after long
75 mm (3") W
periods of continuous use.
342 mm (13.5") H
Vibration will increase with
5100 rpm
the hardness of material.
1400W
Do not operate the tool if
ALL.FG.175240.40 - 230V~, 50Hz
discomfort is experienced,
and ensure that sufficient
ALL.FG.175240.60 - 230V~, 50Hz
rest periods are taken
ALL.FG.175110.40 - 110V~, 50Hz
during cutting. For further
Suits vacuum hose with 35mm
information, contact the
diameter internal taper fitting,
manufacturer.
or 38mm diameter external
taper fitting.
Apply protective hearing, breathing, eyes and body
2mm (1/16") with 15 N (1.5
protection as appropriate.
kg) (3.4 lb) deflection force
With the blades secured and the tool switch OFF, plug
the tool into the power socket.
18 Nm (1.8 kg-m), (13.2ft-lb),
7.7m/s2
5.9m/s2
Do not block the cooling
4.8m/s2
intake vents or ingest
dust or debris at the
92dB (A)
rear of the motor as this
5dB(A)
may cause the motor
to overheat. If working
103 dB(A)
in dusty conditions, it
5dB(A)
is recommended that
the vents be regularly
cleaned with an air blast.
(See Fig.7)
Hold the tool by both the top handle and the motor
housing. (Fig.5 & 6)
To start the cut, hold the tool firmly in your hands and
apply the middle of the blade cutting edge to the work,
keeping in mind that the direction of cut is towards the
rear of the blades.
While cutting, move the tool and blade in a slow
"sawing" motion, which improves the cut rate, reduces
concentrated heat build-up and evens the wear on the
blades. (See Fig.8 & 9)
Fig.5
CAUTION: During
Fig.6
Fig.7
CAUTION:
Publicidad
