Ricatech RTT33 Manual De Usuario página 3

POWER SOURCE
Unwind the power adaptor (Located in a white box inside the packaging foam). First connect the small end of
the adaptor to the back of the turntable, then the other end to an AC power outlet.
UNPACKING THE TURNTABLE
1. Remove packing materials from unit.(Note: Save all packing materials.)
2. Carefully remove unit from its styro-foam and take it out of the plastic bag.
3. Although records can be played with the lid attached and opened, it is recommended
this is removed.
4. Remove the white protective needle cover by gently pulling towards front of unit.
TURNTABLE OPERATION
1. Turn the unit on by rotating the ON-OFF VOLUME SWITCH located on the front panel to the ON position.
2. Release TONE ARM from the ARM LOCK and place it on the ARM REST.
Important: The ARM LOCK is taller than the turntable and needs to be folded down to allow larger
records to be played.
3 Set the SPEED CONTROL SWITCH to desire speed (33 1/3,45 or 78 rpm). Place the record on the
turntable.
4. Lift the TONE ARM by hand to the record and slowly lower it to the desired starting point. The turntable
will start to turn automatically. At the end of the record, the turntable will still turn. You must return the
TONE ARM to the ARM REST manually.
5. Re-adjust the ON-OFF VOLUME SWITCH to the desired level.
NOTE: After use and before closing the cover, always place the TONE ARM back on the ARM LOCK
after this has been pushed upwards again.
ACCESSORY: Adaptor for 45 rpm record
To play the 45 rpm record, place the ADAPTOR on the SPINDLE.
1. Place the 45 RPM adaptor over the spindle.
2. Gently place your 45 RPM record onto the turntable.
3. Follow the steps under turntable operation to play your record.
NEEDLE INSTALLATION
REMOVING NEEDLE:
1. Gently pull down the tip of the cartridge.
2. Pull cartridge forward.
3. Pull out and remove.
INSTALLING CARTRIDGE:
After following ―Remove instructions‖ above, follow steps 1 to 4.
1. Position red cartridge with sapphire stylus facing down.
2. Line up the tab on the back of the needle with the tone arm (as shown in picture 1 below).
3. Insert the cartridge with its front end at a downward angle (as shown in picture 2 below).
4. Lift front end of needle upward until it snaps into place.
All manuals and user guides at all-guides.com
ADDITIONAL INFORMATION:
•
•
•
•
LINE OUT OUTPUTS
1. Connect the auxiliary cables(not supplied) to the LINE OUT JACK and to the auxiliary inputs on the
2. Plug Auxiliary cable into the LINE OUT JACK on the back of your unit.
3. Plug the other end of the Auxililary cable into the input jack on your desired external component.
4. Check the volume level of your external component.
5. See operators manual for correct operation of the external component.
SUBWOOFER OUTPUT JACK
The subwoofer output jack enables you to attach a subwoofer (not supplied) which will enhance bass
response. Please contact your retailer for suitable subwoofer models.
TROUBLESHOOTING GUIDE
THERE IS NO POWER
-
-
TURNTABLE WILL NOT WORK
-
-
-
The red cartridge has a very small sapphire stylus that is barely visible.Take note the replacement needle
you are receiving is the same as the needle already on the tonearm.
This needle is safe for 33 1/3, 45 & 78 speed records.
Replacing the needle depends on how often you use your turntable.
This sapphire stylus will provide an average of 1000 hours playing time.
desired component.
The AC adaptor is not connected to either a power outlet or unit.
The unit is not turned ON : Rotate the ON-OFF SWITCH from the OFF position.
The white protective needle cover was not removed.
Adjust the VOLUME CONTROL knob.
The volume is not turned up.