Volpi VT12 Instrucciones De Uso página 9

chemicals into the environment. Do not tamper with the knapsack sprayer and its components. Do not pressurize the
knapsack sprayer with external equipment (compressors, etc.). Do not unscrew the closure elements if the knapsack
sprayer is under pressure. Before dismantling the knapsack sprayer, release all pressure. Do not pressurize the knapsack
sprayer unnecessarily. Relieve pressure when not in use. Do not tamper with or modify in any way the knapsack sprayer.
Before each use, check the condition of the knapsack sprayer. Do not leave it unattended when the tank is full and under
pressure. The knapsack sprayer should always be placed on a horizontal and flat surface. After the use of the knapsack
sprayer, thoroughly wash the hands, face, and clothing used. Repairs should only be carried out by customer service or
authorized technicians. Use only original spare parts.
FIELDS OF APPLICATION AND CHEMICAL PRODUCTS USED
Hydrochloric acid 20% - Ethyl alcohol - Bleach 0,5% - Cleaners - Hydraulic oils - Synthetic oils - Caustic soda - Amuchina
LIMITED LIABILITY The manufacturer is not liable for damage caused by the knapsack sprayer if such damage is caused
by a failure to heed the instructions for use, improper use, by a repair performed incorrectly or replacement of spare
parts with non-original components, repairs not carried out by the customer service centre or by a trained technician
authorized in writing by the manufacturer himself. The above instruction also apply to components and accessories.
PREPARATION OF THE KNAPSACK SPRAYER
MOUNTING THE LANCE Lower the lever in the direction that you will follow to carry out the treatment.
Check for the presence of the OR on the handle E and screw the barrel L on the handle E (fig. 7). Unscrew the ring N from
the handgrip E and insert it into the pipe G. Stick completely the tip of the pipe G on the rubber holder of the handgrip E.
Tighten until the end the ring N on the handgrip E (fig.7). Mounting the hose: Completely introduce (Fig. 8) the end of the
hose onto the relevant connector of the handle and tighten the ring nut by turning it clockwise. Mounting the shoulder
strap: fold in half the shoulder strap and insert the folded side into the slot under the handle (Fig. 2); secure it then with
the plastic tab. Mount on the two free ends the hooks (Fig. 3) adjusting the length.
CHANGING THE POSITION OF THE THROTTLE FROM LEFT TO RIGHT The knapsack sprayer is supplied with left throttle.
To change the position of the throttle, remove the snap ring that secure the connecting rod on the throttle (Fig. 9-A),
remove the other retaining ring that secure the throttle at the opposite end of the tank (Fig. 9-B). Remove the throttle
from the connecting rod and from the base of the tank (Fig. 9-C). Pull the shoulder straps (Fig. 9-D). Insert the throttle
into the opposite seat (Fig. 10-E). Insert the connecting rod into the throttle (Fig. 10F). Place the brass washer at the end
of the throttle and secure the whole with the pressure mounted snap ring (Fig. 10-G). Replace the snap ring on the
connecting rod, throttle side, by pressure mounting it (Fig. 10-M). Attach the shoulder straps (Fig. 10-N).
FILLING THE TANK Remove the lid and fill the tank by pouring the liquid previously prepared through the filter of the
mouth of the tank. The fluid level must never exceed the bottom of the filter. Replace the cover and screw it tight.
CONDITIONS OF USE Attach the hook of a belt of the shoulder strap, lever side, to the protrusion at the bottom of the
tank (Fig. 5). Insert the arm into the belt just hooked (Fig. 6) and place the knapsack sprayer on the shoulder. Grasp the
other strap, carry it on the free shoulder and hook it in the same way described below for the other side. With the handle
in the closed position, operate the knapsack sprayer until you feel some resistance, then spray, acting on the handle,
continuing pumping regularly. Adjust the jet depending on the treatment to be carried out, by turning the terminal part
of the sprayer. Choose the desired spray pattern (Fig. 7).
AFTER USE Pour all the remaining liquid into a container and rinse thoroughly with clean water inside the tank and the
hose, spraying clean water through the lance nozzle. Check that the filters are clean and that the water used for rinsing
has completely emptied. Close the tap of the handle and store the knapsack sprayer upside down in a clean, dry place
inaccessible to children, protected from sun and frost.
MAINTENANCE Always keep clean, intact and greased all seals, valves, the pumping device and its components. The
breakage or hardening of even one of these components may impair the proper functioning of the knapsack sprayer. Be
careful to correctly reassemble the components. In case of poor dispensing quality, clean the end of the sprayer with
clean water.
TECHNICAL DATA Maximum capacity: 12 litres. Maximum operating temperature: 1°C to 40°C. Maximum operating
pressure: 3 bars
WARRANTY 24 months warranty for private users and 12 months warranty for professional users. The warranty covers
all defects due to bad workmanship or poor materials used. The product, at the discretion of the manufacturer, will be
replaced or repaired free of charge only if it has been used properly, in accordance with the instructions for use, and
without having been tampered with. The warranty does not cover labour, compensation for resulting inactivity period or
any cost for transport. This warranty does not cover parts subject to normal wear: seals, knapsack spraying handle and
its components. Any maintenance operation carried out during the warranty period does not extend in any case its period
of application. The warranty is valid only for products that have been registered through the website within 30 days from
the purchase date. Activate the warranty for your new tool through our website:
Pag. 9 di 16