Carson 50 060 6046 Guia De Inicio Rapido

Charger unit art. nr. 50 060 6046
For charging transmitter and racing batteries
LED1 Racing Pack
LED2 Transmitter
battery / ies
(Tamiya-)
Charging plug
for Racing Pack 7,2V
Safety instructions
Please read the operating instructions before using the unit for
the first time.
Only use the unit in enclosed spaces.
Only for NiMH batteries.
Never attempt to recharge dry batteries.
Ensure that the battery's capacity matches the charging current
of the unit.
Keep small children away from the unit while charging.
Children should only operate the charger unit if supervised by an
adult.
Allow heated batteries to cool prior to charging.
If a battery becomes very hot (>40°C, battery poss. defective),
disconnect the power plug.
Never use the charger as a direct current supplier for electrical
appliances.
Rechargeable battery types
Racing pack 7,2Volt (1,2Vx6 cells, NiMH)
Transmitter battery/ies 4.8Volt
Charging process
Insert the power plug of the charger into a standard domestic
socket outlet. Connect the plug for charging the racing pack (6
cells) to the charger plug,
not apply power.
Insert the plug for charging the transmitter battery/ies (4 cells)
into the charging socket of the transmitter.
The charging of both battery types can occur either individually or
simultaneously.
During the charging process, the charger unit will heat up slightly
• When charging the transmitter batteries (4 cells), the red
LED2 will light up.
• Once these are fully charged (batteries are getting warm),
remove the charger plug from the transmitter.
• When charging the racing pack (6 cells), the red LED1 will
light up.
Specifications
Input voltage AC voltage 230V 50Hz 38 W (max)
60mA max => 14W
Output voltage 1 13.1V +/- 15%
Output voltage 2 8.5V +/- 15%
Output current 1 2A +/- 10%
Output current 2 0.2A +/- 25%
Delta-peak cutoff 140mV max
Cutoff via timer 3hrs
Shorting fuse automatic
Trickle current 130mA max
Fuse Current strength 1.6A
(1,2Vx4 cells, NiMH)
pay attention to the connector force, do
Charging jack for transmitter (4.8V)
Polarity of charging jack
• Once this is fully charged, the charger will change to pulsating
trickle charging, and the LED1 will turn green.
• If the red LED flashes in quick succession, this indicates a
defect. In this case, disconnect the power plug and remove
the battery pack from the charger unit.
Disposal
Please note and understand the symbols on this
product, packaging or instructions. Electronic
components are valuable materials and at the end of
their useful life should not be disposed with
household waste! Help us to protect the
environment and safeguard our resources by
discarding this equipment at a dedicated recycling
point. The authority responsible for waste disposal
or your retailer will be able to answer any questions
you may have in this respect.
Caution
• For use indoor only.
• Disconnect the supply before making or breaking connections
to the battery,
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard,
• Do not disassemble charger, incorrect reassemble may result
in electric shock or fire. - Locate charger as far away from
battery as DC cable permit Never place charger above battery
being charged, gases from battery will corrode and damage
charger.
• These chargers are not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the charger.
without load
without load
without load
at output for 7.2V DC voltage
at output for 4.8V DC voltage
+/- 30 minutes with 6-cell battery pack
with short circuit at output
mean value pulse charging 6 cells
Service-Hotline:
(8.00 Uhr -17.00 Uhr)
(01805) 73 33 00
14 ct/min
Dickie-Tamiya GmbH & Co KG
Mittlere Motsch Str. 9
96515 Sonneberg