Página 1
Vandal-Resistant Surface Mount Dome Housing www.videolarm.com Installation and Operation Instructions for the following models: SM75C2N IP Network Ready, vandal resistant outdoor surface mount housing that can be mount facing down or facing rowards the sky. Clear dome, with 24VAC input, heater/blower, for an...
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth. ELECTRIC SHOCK, DO NOT REMOVE Do not block any of the ventilation openings.
Electrical Specifications Contents of Box SM75C2N Power 24VAC Class 2 Only * Note In cluded with SM75C2NE 24 VAC 3.3 Amps 84 Watts Total Power: 84 Watts Accessories: Heater: 50 Watts/Blower: 2 Watts Camera Power: 32 Watts Max English Tools Required: .100”...
Wall Wall Mounting Mounting WALL Use teflon tape WALL MOUNT Mount only to suitable material such as brick, Use Teflon Tape (included) to seal conduit plugs. concrete, wood, etc. (Wall mount sold separately) • Monte solamente al material conveniente tal como ladrillo, •...
Surface Surface Mounting Mounting Remove the (4) side plates . Mounting Surface Securely mount housing to mounting surface. Replace should be of suitable material such as brick, side plates when complete. concrete, wood etc. • Con seguridad montaje que contiene a la superficie de •...
Página 7
RJ45 24VAC POWER Camera Max 32 Watts Camera Orange Heater/Blower Yellow 26 Watts Heater/Blower Green Alarm 1 Blue Alarm 2 Violet Alarm 3 Gray Common White Make the appropriate male and female connections. Indoor model does not include pre-run cables. •...
Página 8
Use the rubber seal when mounting housing Pull the seal over the face of the dome and up right. Center the seal over the dome. down onto the housing. • Utilice el sello de goma al montar contener encima de la •...
Página 9
Captive Axis 213 (3) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
Página 10
Axis 215 (3) #8x3/8” Mounting Plate 1" 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate using (4) #8 bolts and lock washers. Place (3) #8x3/8” screws on the spacers and line up the mounting slots. Slide plate in and secure. •...
Página 11
AXIS 231-232D AXIS 231-232D Locking screw Loosen Screw Loosen the screw to the right of the tab by Align mounting plate and turn counter- approximately (5) turns. clockwise, secure locking screw. • Alinee la placa de montaje y dé vuelta a la •...
Página 12
Open Screw Slots Cable Ties POWER Camera Power (24VAC) Orange Camera Power (24VAC) CONTROL RJ45 Ethernet Connector ALARMS Alarm 1 Blue Alarm 2 Violet Alarm 3 Gray Common White Captive Screw Complete the wiring to camera. Attach the camera assembly to the housing by sliding the (3) This is what the typical path of illumination will look like with the setting at 30 degrees.
Página 13
Axis 233D Slots Fastener Position camera and mounting plate on top of spacers. Secure quick release turn plate by tightening (3) bolts and (1) fastener. • Asegure la placa rápida de la vuelta del lanzamiento apretando (3) los pernos y (1) la cámara fotográfica del sujetador en la posición usando ranuras.
Página 14
CANON - VB-C10 Captive Screw Mounting Plate (3) #8x3/8” 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
Página 15
ELMO 400/401 Captive (4) #8x3/8” Screw Mounting Plate 1" 1" 2" MOUNTING HOLE MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws, star washer, and nuts. Complete assembly as shown, then secure camera to the quick release plate. •...
Página 16
JVC-VN625U Captive (4) #8x3/8” Screw Mounting Plate ½" 1" MOUNTING HOLE Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release adapter. • Una el soporte rápido del lanzamiento a la placa de montaje usando (4) los tornillos #8 y la arandela de la estrella. Termine a asamblea como cámara fotográfica demostrada, después segura a la placa rápida del lanzamiento.
Página 17
Panasonic KX-HCM180 Captive (3) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE Attach camera bracket to mounting plate using (1) ¼” x 20 bolt, lock washer, and washer. Complete assembly as shown, then secure camera to the quick release plate. •...
Página 18
Panasonic WV-NS954 (4) #8x3/8” Mounting Plate 1" MOUNTING HOLE Attach bracket to (4) spacers using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate el soporte (4) a los espaciadores usando (4) los tornillos #8 y arandela de la estrella. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
Página 19
Sony RZ30 Captive (3) #8x3/8” Screw Mounting Plate ½" 2" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, washer, and lock washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate la cámara a la pletina usando (1) perno de x 20 del ¼”, arandela, y arandela de cerradura. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
Página 20
TOA 2564 Captive (4) #8x3/8” Screw Mounting Plate MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate la cámara a la pletina usando (4) los tornillos #8 y arandela de la estrella. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
Replacement Parts List SM75C2N Wall Mount WMSM7 Sold Separately Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit. Part Number Description RPSM7501 DOME SEAL RPRH7502 LOWER TRIM RING...
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry. Should a problem arise, rest assure that Videolarm stands behind its products by offering some of the most impressive warranty plans available: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on all camera systems (SView, QView, Warriors), and InfraRed Illuminators.