Publicidad
Idiomas disponibles
Idiomas disponibles
To reduce the risk of injury,
•
close supervision is necessary when the light is used near children.
Store idle appliances indoors.
•
When not in use, appliances should be stored indoors in dry and high
or locked-up places – out of reach of children.
Use of accessories and attachments.
•
Use only attachments recommended or sold by the
manufacturer.
Check for damaged parts.
•
A part that is damaged should be properly repaired or replaced by
manufacturer before further use unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by manufacturer. Do not use this appliance if the light mode button does not
turn it on and off.
• Do not operate this unit with a missing or damaged light tube.
• Do not touch the light tube surface at any time.
• Never look directly into the light or shine the light into another person' s eyes.
• Do not disassemble the main body of the unit. Other than the 3 "AA" size dry cell batteries, there are no
user-replaceable parts.
WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:
• Carefully follow all instructions and warnings on the battery label and package.
• Always insert batteries correctly with regard to polarity (+ and –), marked on the battery and the
equipment.
• Do not short battery terminals.
• Do not charge batteries.
• Do not mix old and new, alkaline and rechargeable (nickel cadmium or nickel metal hydride) batteries.
Replace all of them at the same time with new batteries of the same brand and type.
• Remove dead batteries immediately and dispose of per local codes.
• Do not dispose of batteries in fire.
• Keep batteries out of reach of children.
• Remove batteries if the device will not be used for several months.
"Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with
conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation
Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes
(i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits.
So when transporting individual batteries, make sure that the battery terminals are protected and well
insulated from materials that could contact them and cause a short circuit. "
SAVE tHESE INStRUCtIONS
INtRODUCtION
Congratulations on purchasing your new Stanley Work Light.
follow the instructions carefully before using your new work light.
BF01AL_Manual_ENSP_070312.indd 4-5
Read this Instruction Manual and
4
POwER SUPPly
The unit is powered by three "AA" alkaline dry cell batteries (may be sold separately). Unscrew the base
cover screw (counter-clockwise) and remove the base cover. Insert batteries as described in compartment,
observing the cautions that follow. Replace and secure the base cover by screwing the base cover screw
clockwise. Do not be over-tighten.
Note:
Use only "AA" alkaline dry cell batteries in this unit.
CAUTIONS
• When replacing the "AA" alkaline dry cell batteries: Do not mix old and new, alkaline and rechargeable
(nickel cadmium or nickel metal hydride) batteries. Always insert batteries correctly with regard to polarity
(+ and –), marked on the battery and the equipment. Remove dead batteries immediately and dispose of
per local codes.
• Follow all warnings regarding batteries in the Important Safety Instructions section of this manual.
OPERAtINg tHE lIgHt
• Position the unit as desired. Press the light mode pushbutton on the front of the unit.
• Press once for high intensity.
• Press again for medium intensity.
• Press a third time for to turn the light off.
• Press and hold the light mode pushbutton for about five seconds for flashing LEDs.
Adjusting the pivot tube
The pivot tube allows the light to be tilted backward and forward to direct the illumination upward or
downward.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• Do not attempt to "force" the pivot tube beyond its maximum angle.
• The pivot tube was designed to tilt forward and backward only.
• The pivot tube was designed to be used when the unit is hanging or attached to a surface using its
magnetic base. Using it when the unit is placed on a level, non-metallic surface may cause the light to fall
over and sustain damage.
• NEVER attempt to rotate the light tube itself. Always use the pivot tube to adjust the area of illumination.
Using the hanging hook and magnetic base
The hanging hook and magnetic base allow you to position the light for convenient, hands-free operation.
The hanging hook rotates 360° to direct illumination as needed.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is hung by the hanging hook or attached using the magnetic base, do not shake the light or
object that it is hanging from or attached to. Do not hang the light from or attach the light to any electrical
wires or anything that it is not secure.
• Only use the hanging hook for hanging the light. The hanging hook is not intended to support additional
weight. Do not attach or hang anything additional to the light or risk of breakage may occur.
5
7/16/2012 10:52:15 AM
Publicidad
