Safety Standards; Assistance Service - Peg-Perego MAXI EXCAVATOR Empleo Y Manutencion

SAFETY STANDARDS

Our toys are compliant with European Safety
Standards for toys (safety requirements stipulated by
the EEC Council) and with the "U.S. Consumer Toy
Safety Specification". They are also certified by
notified toy safety bodies in accordance with
Directive 2009/48/EC. They are not compliant with
the requirements of road transport standards and
consequently cannot travel on public roads.
Peg Perego S.p.A. is ISO 9001
certified.
This certification provides customers
and consumers with a guarantee of
transparency and assurance about the
company's working procedures.
• A child must be 2 year of age or older for the
necessary coordination and maturation to operate
this motorized vehicle safely.
• WARNING! Using the vehicle on public roads, in
narrow spaces or near watercourses and
swimming pools may cause injury to the users
and/or third parties. Adult supervision is always
necessary.
• Children must always wear shoes when using the
vehicle.
• When the vehicle is in operation make sure that
children do not put their hands, feet, other body
parts, clothing, or other objects close to the
moving parts.
• Never wet sensitive vehicle components like the
motors, electrical systems, buttons, etc.
• Do not use petrol or other flammable substances
close to the vehicle.
• The vehicle must be only be used by a single child
unless it is classed as a two-seater vehicle.
WEEE DIRECTIVE (EU only)
• At the end of its useful life, this product is classed
as Waste Electrical and Electronic Equipment
(WEEE) and must therefore not be disposed of as
urban waste but instead taken to a designated
separated waste collection facility.
• Take it to an appropriate collection centre.
• The presence of dangerous substances contained in
the electrical components of this product
represents a potential source of danger to human
health and for the environment if the products are
not disposed of correctly.
• The barred dustbin symbol indicates that the
product must undergo sorted waste collection.
DISPOSAL OF THE BATTERY
• Help protect the environment.
• Used batteries must not be disposed of with
domestic waste.
• They can be left at a used battery or special waste
collection centre. Contact your local authorities
for more information.
LR44 BATTERY WARNINGS
The insertion of the batteries must be carried out
and supervised by adults only. Do not allow children
to play with the batteries.
• The batteries must be replaced by an adult.
• Only use the battery type specified by the
manufacturer.
• Respect the +/- polarity.
• Do not short circuit the power supply terminals:
risk of fire or explosion.
• Always remove the batteries when the toy is not
used for a long time.
• Do not throw the batteries into a fire.
• Never try to recharge batteries if they are not
rechargeable.
• Do not mix old and new batteries.
• Remove flat batteries.
• Dispose of flat batteries in the appropriate
recycling containers.
MAINTENANCE AND VEHICLE CARE
• Regularly check the conditions of the vehicle. In
case of fault, do not try to use the vehicle. For
repair use only original PEG PEREGO's spare parts.
• PEG PEREGO assumes no liability if the product as
been tampered with.
• Do not leave vehicle near sources of heat such as
radiators, stoves, fireplaces, etc.
• Protect vehicle from water, rain, snow, etc.
• Periodically lubricate (with a light weight oil)
moving parts, such as wheel bearings, steering
linkages, and chains at points of rotation or where
they come in contact.
• The vehicle's surface can be cleaned with a
dampcloth. Do not use abrasive cleaners. The
cleaning must be carried out by adults only.
• Never disassemble the vehicles mechanisms unless
authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.

ASSISTANCE SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-site/support/
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and
valuable to us. We would be very grateful if, once
you have used the product, you would fill out the
CONSUMER SATISFACTION QUESTIONNAIRE
which you can find on the internet at:
www.pegperego.com, making any observations
or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING.
ASSEMBLY
1 • Position the seat in one of the two possible
positions on the seat support that will best suit
the child's height.
Seat position A - low and forward;
Seat position B - high and to the rear.
2 • Secure the seat in the desired position using the
two screws provided.
3 • Slide the two front studs of the seat support
into the relating holes on the frame.
4 • Secure the rear of the seat support to the
excavator frame using the two screws provided.
5 • Position the roll-bar to the excavator by sliding
both ends of the bar into the slots on the rear
mudguards.
Note: the roll-bar should lean slightly towards
the rear of the excavator.
6 • Secure the roll-bar in position with the two
screws supplied (one on each side).
7 • Turn the red coupling pin so that the cab can be
opened (1). Release the cab. Fully insert the hinge
at the front of the chassis (2). Close the cab (3)
and secure it by turning the red pin 180°.
8 • Combine the upper and lower parts of the
steering wheel together.
9 • Fit the horn into the hole in the middle of the
steering wheel following the instructions on the
packaging.
10 • Push the steering wheel shaft (1) upwards and
line up the holes on both components (2).
11 • Position the nut in the hexagonal hole and the
bolt in the round one. Secure the steering wheel
in position by tightening up the bolt.
12 • Remove the protective caps from the front and
rear axles.
13 • Fit a washer to the front left axle. Fit the small
wheel with the letters SX stamped on the inside
Note: before fitting the wheel, make sure that
the wheel has a hub cap with a bushing on the
inner side.
14 • Fit a washer to the end of the axle that is
protruding from the wheel.
15 • Position a self-locking washer on the conical
retaining cap as shown in the photo. Warning, the
tabs on the self-locking washer must be
positioned face down. Note: the bag contains
more self-locking washers than required, keep
the extras as spares for use in the event of a
breakage.
16 • Fasten the wheel to the axle with a hammer.
Carry out the same procedure on the right front
(DX).
17 • Starting on the left side of the excavator, first fit
the big wheel with the letters SX stamped on
the inside, to the rear axle making sure that the
splined section of the axle is fully inserted inside
the wheel.
Note: before fitting the wheel, make sure that
the wheel has a hub cap on the outside and a
bushing on the inner side.
18 • Fit a washer to the end of the axle that is
protruding from the wheel.
19 • Position a self-locking washer on the conical
retaining cap as shown in the photo. Fasten the
wheel to the axle with a hammer.
20 • Place the excavator on its left side. Position a
conical retaining cap under the left wheel (1). Fit
the right rear wheel (DX) to the axle. Slide a flat
washer on to the part of the axle that is
extruding. Position a self-locking washer on the
conical retaining cap and fasten the wheel to the
axle with a hammer (2).
21 • Press the hub caps into position on the wheels
(large to the rear and small to the front).
22 • Fit the two silver stickers to the rear mudguards.
23 • Click the rear light clusters into the lower (1)and
upper (2) position
24 • Fit the silver stikers to the front head light.
25 • Click the cover of the front light into place,
ensuring you insert the side tongues into the
mask slots.
26 • Fit one of the two cross members between the
excavator bucket arms using slots nearest the
shovel.
27 • Secure it in position with the two screws
supplied (one on each side).
28 • Fit the other cross member between the
excavator bucket arms.
29 • Secure it in position with the two screws