Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CABLE
ACE
OUTPUT
IN
Set-Top Box
AV1 :
L + R + VIDEO
4
OUT
IN
Set-Top Box
Watching Cable TV programs that don't
require the cable box
Since you've connected the cable TV signal
directly to the TV's tuner, you can also watch the
unscrambled programs by simply tuning to the
desired channel. You must first use Autoprogram,
however, to store channels in the TV's memory.
See page 8.
Note: This connection will supply stereo sound to
the TV if it is being broadcast by the station you are
watching.
English_DFU_37131.indd 3
CABLE
75
conn us entry05 cable.eps
HDMI 1
HDMI 2
75
TO TV
2
OUT
3
CABLE
1
2
SIGNAL
SPLITTER
3
conn us entry05 cable RF.eps
file : conn us entry05 cable AV.eps
Basic connections to the TV
&
Your integrated digital TV automatically decodes and displays the four basic DTV
picture resolution standards.
- SDTV (Standard Definition TV) are broadcast as 480i (480-line interlaced) or
480p (480-line progressive scan) video.
- HDTV (High-Definition TV) are broadcast either in the 1080i or 720p formats,
always with a widescreen picture.
Note: Progressive scan video (p) is more like that you see in a movie theater. Images are
much more distinct and free of flicker, and motion is smoother.
Next to analog NTSC broadcast reception, your TV has an integrated High
Definition TV tuner which receives, decodes and displays terrestrial ATSC and
unscrambled cable (QAM) signals.
HDTV quality is only reproduced when a broadcaster or cable provider broadcasts
HDTV signals.
Note: Ask your broadcaster or cable box provider to transmit/enable HD content to your
home, and possibly upgrade to a CableCard for the decription of HD signals.
There are 2 ways to get HDTV content:
- via cable,
- via antenna.
Note: This drawing is used wherever you can connect cable or antenna.
- Cable TV
Connect the cable TV signal to the
of the TV. See page 8 for details on using Autoprogram to store channels in the
TV's memory.
Note: this connection will supply stereo sound to the TV if it is being broadcast by the
station you are watching.
- Cable box with
RF IN/OUT
• Connect the incoming cable TV signal to the cable
the cable box.
• Connect a coaxial cable (not supplied) from the
cable box to the
CABLE/ANTENNA 75 Ω
Note: Your cable box may have a different label for the
or
.
OUTPUT
OUT
• Set the
switch 3 of the cable box to
OUTPUT CH
correct for your cable box), then tune the TV to the corresponding channel.
Once tuned, change channels at the cable box, not the TV.
Note: This connection will not supply stereo sound to the TV. The reason is that the RF
output on a cable box - labeled
stereo signal to the tuner (VHF/UHF) input on a TV.
- Cable box with A/V outputs
• Connect the incoming cable TV signal 1 to a signal splitter (not supplied).
The signal splitter enables you to avoid having to use the TO TV jack on the
back of the cable box. This jack will not supply stereo sound to the TV.
Note: Your cable box may have a different label for the
or
.
OUTPUT
OUT
• Connect a coaxial cable (not supplied) to a connector on the signal splitter and
to the
CABLE/ANTENNA 75 Ω
• Connect another coaxial cable (not supplied) to a connector on the signal
splitter and to the cable
IN
• Connect A/V cables (not supplied) to the
on the back of the cable box and to the
(labeled
and
) jacks 4 on the back of the TV.
AUDIO
L
R
• To view programs from your cable box, first press the
remote control.
• Press the cursor down or up buttons until the
• Press the
button to confirm your selection. The
OK
becomes current for the viewing of cable TV programs through your cable box.
Note: If your cable box Audio/Video outputs will not supply video and stereo audio to
the TV, you will need to make the connection shown above in the example "Cable box
with
".
RF IN/OUT
3
x jack at the bottom
CABLE/ANTENNA 75 Ω
jack 1 on the back of
IN
jack on the back of the
TO TV
x jack 2 at the bottom of the TV.
jack, such as
TO TV
or
CH 3
,
or
for example - will not send a
TO TV
OUT
OUTPUT
jack, such as
TO TV
x jack 2 on the TV.
jack 3 on the back of the cable box.
and
VIDEO
AUDIO L
video (labeled
AV2
VIDEO
button on the
AV+
signal source is selected.
AV2
input source
AV2
(whichever is
4
and
outputs
R
) and
2006-03-29 6:30:48 PM
Publicidad
Capítulos
Tabla de contenido
