Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTALLATION INSTRUCTION
FOR EL850 SINGLE CYLINDER
COMPRESSOR 4 HOLE BASE MOUNT
NATURALLY ASPIRATED
AIR COOLED
WATER COOLED
KN85020
KN86020
KN85020X
KN86020X
L31043
Rev. 6/02
4.91
• ASK THESE QUESTIONS:
1.
Is the compressor to be replaced a side or top discharge?
2.
Will the dive pulley interfere with the cylinder block?
3.
Are all water ports 1/2" NPT?
(EL850 ports are all 1/2").
4.
Will additional lines and fittings be required to relocate
the governor?
5.
Will additional water lines and fittings be required for
installation?
Air Cooled
6.
Is adequate air flow available for air cooled models?
• OPTIONAL INSTALLATION CHOICES:
1.
Remote or direct mount governor.
2.
Remote or direct mount air cleaner.
3.
Head can be rotated to any 90º position.
4.
The rear end cap can be rotated to allow ease of oil line
hook-up.
5.
Can be naturally aspirated intake or turbocharged intake (refer
to Air Inlet section on reverse side of this booklet).
6.
Air or water cooled models are available.
KN85020
Air Cooled
EL850
11.00
2.22
10.08
KN86020
Water Cooled
EL850
11.00
4.95
• CHANGEOVER MATERIALS THAT MUST BE
SUPPLIED:
1. The EL850 requires no discharge manifold - use 1/2" pipe to
discharge line fittings.
2. Possibly need 1/2" to 3/8" water port reducers.
3. If replacement is charged to naturally aspirated - supply KN19040
and plug the turbocharger port on the engine.
• CHANGEOVER MATERIAL THAT SHOULD
BE CONSIDERED:
1. For ease of changeover and extended life of the compressor use
the KN17500 series flexible Teflon discharge line kit.
2. Let the compressor breathe - use a KN19040 heavy duty filter.
3. Universal water line kit, SN3502 to hook-up coolant lines.
• CHANGEOVER MATERIAL THAT MIGHT BE
REQUIRED
1. Remote mount governor kit SN4011B.
2. Inlet check valve kit SN3711AJ can be used to reduce unloaded
horsepower requirements and for installations which have
demonstrated excessive oil consumption.
3. If the discharge and adjacent water port both require elbow fitting, it
may be necessary to extend the water port with a pipe fitting.
2.22
10.08

Publicidad

loading

Resumen de contenidos para Haldex KN85020

  • Página 1 KN85020 KN86020 L31043 Air Cooled Water Cooled Rev. 6/02 EL850 EL850 11.00 11.00 2.22 2.22 4.91 4.95 10.08 10.08 • ASK THESE QUESTIONS: • CHANGEOVER MATERIALS THAT MUST BE Is the compressor to be replaced a side or top discharge?
  • Página 2: Air Inlet

    Elbow 1/2” ................b KN18530X Hose Fitting 1/2” Pipe to 1/2” Hose........b Water Hose 1/2” ID ..............b The Haldex inlet check valve SN3711AJ offers a low cost KN18537 Hose Clamp 1/2” ..............b method to reduce the nominal unloader horsepower (as Hose To Hose Coupling 1/2” ..........b compared to a clutch).
  • Página 3 Intake Manifold Options 5) Unbolt fuel pump on Cummins and power steering HEAD ROTATION pump on some Mack models. The head assembly of any EL850 Air Compressor can be 6) Remove mounting bolts on flange-mounted units. rotated with respect to the block. A head rotation may be Remove bottom bolt(s) first.
  • Página 4 A. Close before starting engine. Maximum Pulley Offset 3 inches A. See front side for Haldex recommendations. The line must be Excessive force on the crankshaft could result in short bearing life Start Engine .547 inch ID Minimum, show no bends smaller than a two inch and a broken crankshaft.
  • Página 5 KN85020 KN86020 L31043 Enfriado por aire Enfriados por agua Rev. 6/02 EL850 EL850 11.00 11.00 2.22 2.22 4.91 4.95 10.08 10.08 • MATERIALES DE INTERCAMBIO QUE SE DEBEN SUMINISTRAR: • REALICE LAS SIGUIENTES PREGUNTAS: 1. El EL850 no necesita múltiple; utilice una tubería de 1/2"...
  • Página 6: Entrada De Aire

    Tuerca del cigüeñal ............a,d El puerto de entrada puede estar conectado al conducto Chaveta ................b KN18530 que filtra el aire del motor o al filtro de aire Haldex Recodo de 1/2" ..............b KN18530X KN19040. Tubería de 1/2" del empalme de manguera a manguera de 1/2"..............b...
  • Página 7: Rotación Del Cabezal

    ROTACIÓN DEL CABEZAL Opciones del múltiple de entrada 6) Retire las sujeciones sobre las unidades montadas en brida. Primero, retire los tornillos de la parte inferior. El ensamble del cabezal de cualquier Compresor de aire EL 850 PRECAUCIÓN Un compresor de aire pesa entre 10 y 23 puede rotarse con respecto al bloque.
  • Página 8 Contrapeso máximo de la polea 3 pulgadas Depósito A. Consulte las recomendaciones de Haldex en el anverso. El del aire La fuerza excesiva en el cigüeñal puede provocar que se quiebre conducto debe ser de 0.547 pulgadas ID como mínimo, sin ángulos Conducto de escape descarga y que su vida útil disminuya.

Este manual también es adecuado para:

Kn86020