Cleaning And Storage; Optional Accessory; Troubleshooting Chart; Specifications - Cub Cadet ST228 Manual Del Operador

CLEANING AND STORAGE

WARNING:
To avoid serious personal injury, always turn the unit off and allow it to cool
before you clean or service it.
CLEANING
Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners
that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic
housing or handle. Wipe off any moisture with a soft cloth.
STORAGE
• Never store a fueled unit where fumes may reach an open flame or spark.
• Allow the engine to cool before storing.
• Store the unit locked up to prevent unauthorized use or damage.
• Store the unit in a dry, well-ventilated area.
• Store the unit out of the reach of children.
Short Term Storage (1-2 weeks)
1. Store the unit in a horizontal position. If this is not possible, store the unit vertically with the engine at
the top.
Long Term Storage
If planning on storing the unit for an extended time, use the following storage procedure:
1. Drain all fuel from the fuel tank into a container with the same 2-cycle fuel mixture. Do not use fuel
that has been stored for more than 30 days. Dispose of the old fuel/oil mix in accordance with
federal, state and local regulations.
2. Start the engine and allow it to run until it stalls. This ensures that all fuel has been drained from the
carburetor.
3. Allow the engine to cool. Remove the spark plug and put 5 drops of high quality motor oil into the
cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the unit
after storage.
4. Thoroughly clean the unit and inspect it for any loose or damaged parts. Repair or replace damaged
parts and tighten loose screws, nuts or bolts. The unit is ready for storage.

OPTIONAL ACCESSORY

ELECTRIC STARTER AND POWER START BIT™
FEATURES
This unit is designed to be started with an optional
electric starter or Power Start Bit™ that are sold
separately. If choosing to start the unit using one of these
features or have questions please contact your local
retailer or call 1-877-282-8684 U.S, (1-800-668-1238
Canada), for more information and purchasing. You may
also go to www.cubcadet.com or www.cubcadet.ca
6
ENGINE WILL NOT START
Empty fuel tank
Primer bulb wasn't pressed enough
Engine is flooded
Old or improperly mixed fuel
Fouled spark plug
ENGINE WILL NOT IDLE
Air filter is plugged
Old or improperly mixed fuel
Improper idle speed
ENGINE WILL NOT ACCELERATE
Old or improperly mixed fuel
Cutting head bound with grass
Dirty air filter
ENGINE LACKS POWER OR STALLS
Old or improperly mixed fuel
Fouled spark plug
ENGINE STOPS WHILE IN USE
Engine overspeed protection engaged
CUTTING ATTACHMENT WILL NOT ADVANCE LINE
Cutting attachment bound with grass
Cutting attachment out of line
Line twisted when refilled
Not enough line is exposed
IF FURTHER ASSISTANCE IS REQUIRED, CONTACT AN AUTHORIZED SERVICE DEALER.
Electric Start Feature
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 2-Cycle
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10 in. (2.794 cm)
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 cc
Operating RPM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,500+ rpm
Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,200 - 3,400 rpm
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 in. (0.635 mm)
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel/Oil Mixture
Fuel/Oil Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50:1
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 fl.oz. (414 ml)
Total Approximate Unit Weight (without fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 13 lbs. (5 - 6 kg)
Cutting Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Proulx™
Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Included
Line Spool Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 in. (114.3 mm)
Trimming Line Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.095 in. (2.41 mm)
Cutting Path Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 in. (45.72 cm)
* All specifications are based on the latest product information available at the time of printing. We
reserve the right to make changes at any time without notice.
TROUBLESHOOTING
CAUSE

SPECIFICATIONS*

ACTION
Fill fuel tank with properly mixed fuel
Press primer bulb fully and slowly 10 times
With choke lever in position 3, squeeze the trigger and
pull the starter rope
Drain fuel tank and add fresh fuel mixture
Replace or clean the spark plug
Replace or clean the air filter
Drain fuel tank and add fresh fuel mixture
Adjust according to the Idle Speed Adjustment section
Drain fuel tank and add fresh fuel mixture
Stop the engine and clean the cutting head
Clean or replace the air filter
Drain fuel tank and add fresh fuel mixture
Replace or clean the spark plug
Allow the engine to cool down for 10 minutes before
restarting.
Stop the engine and clean cutting attachment
Refill with new line
Remove and rewind the line
Push the bump knob and pull out line until 4 inches (102 mm)
of line is outside of the cutting attachment