La-Z-Boy PowerReclineXR+ Manual Del Usuario página 8

Battery Backup ssembly Instructions
-- Replace the power supply batteries every six months and
NOTICE: after each power failure use. Under normal conditions, the
battery backup will operate the chair two times, but this
performance cannot be guaranteed.
The performance of the built-in battery backup cannot be guaranteed. If you require continuing
use during a power outage, you should purchase a separate battery backup system. Contact
your La-Z-Boy ® dealer for more information.
The operating speed is reduced to decrease energy consumption.
Always maintain constant even pressure on the button when operating on battery backup to
reduce the energy consumption.
The battery backup is located in the power supply and uses two 9-volt alkaline batteries (not included).
1. Unplug the 120 volt power cord from the electrical outlet, and disconnect the power supply
connector from either the Y-cable connector or motor connector.
2. The battery compartment is located in the bottom of the power supply. Slide the battery
cover over to access the battery compartment.
3. Snap the connection caps on the battery terminals. Place the batteries in the power supply.
4. Slide the battery cover over the batteries.
5. Repeat steps 1 - 4 for each power supply.
6. Proceed to the Operating Instructions.
Power
Supply
PowerReclineXR & PowerReclineXRw
+
®
Input: 100V-240V ~ , AC 50/60 Hz 1.5A
Output: 29V DC 2.5A
14
Battery
(2) 9-Volt
Alkaline Batteries Cover
Supply Specifications:
+
TM
+ & PowerReclineXRw +
PowerReclineXR
®
Operating Instructions
– To reduce the risk of electric shock, serious
DANGER
injury or death:
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
WARNING
– To reduce the risk of serious injury:
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
+ and PowerReclineXRw +
• The PowerReclineXR ®
not exceeding 300 pounds per seat. Do not operate an individual seat with more than
one occupant in or on any part of the individual seat.
• To safely exit the unit and prevent a tripping hazard, bring the back upright
and close the legrest.
• Keep hands, arms and body parts away from the open area between a reclined back
and an upright back on a motion sofa or modular. This area must remain clear at all
times to provide unobstructed movement and prevent injury that could occur when a
reclined back is returning toward the upright
NOTICE: -- After 1 minute of continuous operation, allow the system to
rest for 9 minutes.
Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running
from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.
+ and PowerReclineXRw +
The PowerReclineXR
®
adjustment positions for the headrest and lumbar for the ultimate in customized comfort:
• Only recline the back. When the back is reclined, the PowerReclineXR
• Only extend the legrest. When the legrest is extended, the chair body tilts backward.
• Operate both the back recline and legrest extension simultaneously.
• Position the headrest forward when reclined, stopping in any one of the various angles of support.
• Increase the intensity of the lumbar support stopping in any one of the various levels
for optimal lower lumbar support.
To recline, press and hold down one of the three reclining option buttons on the right side of the
hand wand. Release the button when you have reached a comfortable position.
To return to the upright position, press and hold down one of the three return buttons on the left
side of the hand wand. Release the button when you have reached a comfortable position, or
when the back is fully upright and the legrest is fully closed.
To rotate the headrest forward, press and hold down the button on the right. To return the
headrest to the upright position, press and hold down the button on the left. Release the button
when you have reached a comfortable position, or when the headrest is fully retracted.
To increase lumbar intensity, press and hold down the button on the right. To decrease the
lumbar intensity, press and hold down the button on the left. Release the button when you have
reached a comfortable level, or when the lumbar is fully retracted.
The function of each hand wand button is explained in greater detail on the following page.
Unplug the power supply if you are going to be away from your residence for an extended period of time.
TM
units are intended for a single occupant
TM
position.
offer three reclining options along with several
TM
+ can be rocked.
®
15