Standard Equipment; Brief Description - Virutex SR210 Manual De Instrucciones

2. SPECIFICATIONS
Voltage..............................................220/240 V 50/60Hz
Imput power......................................................1,900 W
No-load speed......................................................5,000/min
Saw diameter.....................................................210 mm
Max/min saw diameter..............................210/200 mm
Max/min set width.................................................2.4 mm
Saw blade hole diameter.......................................30 mm
Depth of cut at 90°..................................................75 mm
Depth of cut at 45°..................................................53 mm
Depth setting.........................................................0-75 mm
Inclination setting.....................................................0-45º
Weight.......................................................................5.9* Kg
Acoustic pressure level A..................................91.8 dBA
Acoustic power level A.................................102.8 dBA
Wear ear protection!
Vibration total values.......................................1.77 m/s
3. RECOMMENDATIONS
Follow very carefully the instructions in this manual,
save itand keep it close at hand, ready to carry out any
inspection of parts that may be necessary.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in thi this manual. Any other
use of the tool is strictly forbidden.
Before using the tool, make sure the mains voltage is
correct, it must be the same as that on the specifica-
tion label.
Machines with 230 V can also be connected to a 220
V mains supply.
Before plugging in the tool, always make sure the control
switch K works properly and returns to the OFF position
when released.
4. PICTURES
DESCRIPTION (See pictures)
A) Saw blade (Fig. 1)
B) Riving knife setting screw (Fig. 1)
C) Mobile blade guard (Fig. 1)
D) Saw blade setting disc (Fig. 1)
E) Disc setting screw (Fig. 1)
F) Riving knife (Fig. 1)
G) Depth setting wing nut (Fig. 2)
H) Fence setting wing nut (Fig. 3)
I) Fence
J) Safety push button switch (Fig. 2)
K) On/Off switch (Fig. 2)
M) Angle setting wing nut (Fig. 3)
N) Sawdust extraction (Fig. 1)
P) Button (Fig. 3)

5. STANDARD EQUIPMENT

- Fence
- Saw blade key
- Instructions manual and other documentation.
-1
- Base plate protection

6. BRIEF DESCRIPTION

This tool is specially designed for straight sawing only
of boards made from wood and derivatives (plywood,
chipboard etc...).
7. START UP
Only plug in the machine when the switch
is in off position.
2
Press the locking button J, and squeeze the trigger in
the on/off switch K. When the on/off switch is released,
the machine stops.
8. FITTING THE SAW BLADE
Always unplug the machine before ca-
rrying out any work on it.
CAUTION: Do not use bent or cracked blades or high-
speed steel blades. Do not use saw blades that do
not conform to the specifications contained in these
instructions.
1. Move the mobile guard C backwards and hold it in place.
2. To loosen or tighten the screw E with the key supplied
with the machine, secure the blade shaft with the aid
of the push button P (Fig. 3).
3. Loosen the screw E and remove the setting disc D.
4. Fit the saw blade and tighten with the setting disc
D and the screw E.
5. Before fitting the new blade, make sure the surfaces
in contact with the setting discs are clean. The teeth
of the saw should protrude beyond the riving knife F.
(The arrow printed on the fixed guard of the machine
indicates the cutting direction of the teeth).
9. SETTINGS
1. Cutting depth setting
For a clean perfect cut, the cutting depth should be
adjusted to the thickness of the wood to be worked on,
so that the saw blade protrudes a tooth's height from the
material. To adjust the cutting depth, loosen the wing
nut G and move the machine upwards or downwards.
The scale printed on the parallel guide indicates the
cutting depth.
9