EINHELL GE-CM 36/37 Li Manual De Instrucciones Original página 25

Ocultar thumbs Ver también para GE-CM 36/37 Li:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 99
Charging the battery (Fig. 11)
1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 12/
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(19) into the socket outlet. The green LED will
then begin to fl ash.
3. Slot the battery pack or packs (18) onto the
battery charger (19).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
whether there is voltage at the socket outlet
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
the charging unit
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Battery capacity indicator (Fig. 12)
Press the switch for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
Anl_GE_CM_36_37_Li_SPK7.indb 25
Anl_GE_CM_36_37_Li_SPK7.indb 25
GB
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
Installing the battery (Fig. 13)
Open the battery cover. Then insert the batteries
in the mounts as shown in Fig. 13.
Important!
The equipment's operating time depends on
the battery with the lower charge level or lower
capacity (Ah). Therefore, only use rechargeable
batteries which are charged to the same level and
have the same capacity (Ah). Never combine full
and half-full batteries or batteries with diff erent
capacities (Ah). Always charge the two batteries
simultaneously before starting to use them.
Close the battery cover by fl ipping the cover
down.
6. Operation
Caution!
The lawn mover is equipped with a safety circuit
to prevent unauthorized use. Directly before star-
ting up the lawn mover insert the safety plug (Fig.
14/Item 17) and remove the safety plug again
whenever you interrupt or terminate your work.
Important!
To prevent the equipment switching on acciden-
tally, the lawn mower is equipped with a safety
switch (Fig. 15/Item 2) which must be pressed be-
fore the switching bar (Fig. 15/Item 3) can be ac-
tivated. The lawn mower switches itself off when
the switching bar is released. The start time can
amount to several seconds. Repeat this process
several times so that you are sure that the ma-
chine functions properly. Before you perform any
repair or maintenance work on the equipment,
ensure that the blade is not rotating and that the
safety plug is disconnected.
- 25 -
26.04.2021 08:29:37
26.04.2021 08:29:37

Publicidad

Tabla de contenido
loading

Tabla de contenido