Cleaning & Maintenance - Broan Elite EW5630SS Manual De Instrucciones

MAKE-UP AIR DAMPER
The hood is compatible with Broan Make-Up Air Damper Model
MD6T or Model MD8T (optional). Purchase separately.
Make the connection to the Make-Up Air Damper with low voltage
wiring, as shown. See Make-Up Air Damper instructions for additional
information.
MAKE-UP AIR DAMPER
24V
TRANSFORMER
(INCLUDED)
GRD
120 VAC
60 HZ
REMOTE CONTROL
This hood is compatible with Broan Radio Frequency (RF) Remote
Control Model BCR1 (optional). Purchase separately.
Conduct the following steps to link the BCR1 remote control with the
hood:
1. On the hood, press and hold the LIGHT button for 3-seconds and
then release it.
2. The blue LED indicators will turn on and off in succession to
indicate the hood is in RF linking mode.
3. When the hood is in the linking mode, press any key on the RF
remote.
4. An audible beep will be heard from the hood and the blue LED's
will stop blinking, which indicates a successful hood and remote
control link.
• If the remote control did not successfully link with the hood
and no further action is taken, the linking mode will deactivate
after 12 seconds and the blue LED's will stop blinking
sequentially.
• Refer to the BCR1 instructions for additional information.
Conduct the following steps to erase a remote control link with the
hood:
1. On the hood, press and hold the LIGHT button for 3-seconds
seconds and then release it.
2. The blue LED indicators will turn on and off in succession to
indicate the hood is in RF linking mode.
3. Press and release the OFF button.
4. The blue LED indicators will turn on and off together three times
to confirm the link is erased.
• If the hood did not successfully erase the remote control link and
no further action is taken, the linking mode will deactivate after
12 seconds and the LED's will stop blinking sequentially.
• Refer to the BCR1 instructions for additional information.
CLEANING & MAINTENANCE
For performance, appearance, and health reasons, clean filter, fan
and grease-laden surfaces. Use only a clean cloth and mild detergent
solution on stainless and painted surfaces.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filter may occur if using phosphate
detergents, or as a result of local water conditions - but this will not
affect filter performance. This discoloration is not covered by the
warranty.
MAKE UP DAMPER CONNECTION
(switched low voltage)
20 GAUGE BELL WIRE FOR LOW
VOLTAGE CONNECTION ON
TOP OF HOOD
DRY CONTACT
TERMINAL
BUSHING
HOOD
FOR LOW
VOLTAGE
CONNECTION
MODELS EW5630SS • EW5636SS
Clean the non-duct recirculating filter surfaces frequently with a
damp cloth and a mild detergent. DO NOT immerse filters in water
or put in dishwasher. Change the non-duct recirculating filters every
6 months. For replacement non-duct recirculating filters - purchase
S99010365 or Model FILTERE56.
The motor is permanently lubricated and never needs oiling. If the
motor bearings make excessive or unusual noise, replace the blower
assembly with an exact service replacement.
LIGHT BULBS
HALOGEN
BULB
(2)
ROTATE
CLOCKWISE
WARNING
Bulbs may be hot. Always allow bulbs to cool down before removing
them.
Use (2) Halogen Bulbs (included with hood) - 120 V, 35 W, shielded
halogen bulbs - MR16 with GU10 base.
NOTE
Suction Cup Tool (included with hood) can be used to install and
remove light bulbs. Align pins on bulb with large diameter opening
on socket, then push bulb in towards hood and rotate clockwise
until firmly seated. The position of the bulb socket (depth) is
adjustable and may require adjustment when: a) certain brands of
bulbs are difficult to install. b) the bulb protrudes too far below the
light panel.
LAMP SOCKET
BRACKET
LIGHT
PANEL
To change the depth of bulb sockets:
- Remove 2 screws on light panel – set screws aside
- Remove Light Panel.
- Loosen 2 Screws holding Lamp Socket Bracket to Light Panel.
- Adjust socket/bracket to desired depth.
- Re-tighten screws securely.
- Re-attach light panel with 2 screws that were previously set aside.
Page 8
SUCTION
CUP TOOL
(1)
PUSH IN
SCREWS