Safety Instructions - Hammerhead HLMT130 Manual Del Usuario

SAFETY INSTRUCTIONS

Safety Instructions for Compact Laser Measuring Tool
WARNING
LASER RADIATION. Do not stare into beam.
ClassII laser product. Turn the laser beam on
only when using this tool.
• Do not remove or deface any product
labels.
• Avoid direct eye exposure. The laser
beam can cause flash blindness.
• Do not operate the tool around children or
allow children to operate the tool.
• Do not place the tool in a position
that may cause anyone to stare at the
laser beam, whether intentionally or
unintentionally.
• Do not use on surfaces such as sheet
steel that have shiny, reflective surfaces.
The shiny surface could reflect the beam
back at the operator.
• Always turn the laser tool off when not in use. Leaving the tool on
increases the risk of someone inadvertently staring into the laser beam.
• Do not attempt to modify the performance of this laser device in any way.
This may result in a dangerous exposure to laser radiation.
• Do not attempt to repair or disassemble the laser-measuring tool. If
unqualified persons attempt to repair this product, serious injury may occur.
Any repair required on this laser product should be performed only by
qualified service personnel.
COMPACT LASER MEASURING TOOL
AVOID EXPOSURE/EVITE LA EXPOSICIÓN/
ÉVITEZ L'EXPOSITION
LASER RADIATION IS EMITTED FROM THIS APERTURE
LA RADIACIÓN LÁSER SE EMITE DE ESTA ABERTURA
CET OUTIL PRODUIT UN RAYONNEMENT LASER
CAUTION
PRECAUCIÓN
ATTENTION
LASER RADIATION – DO NOT STARE INTO BEAM
RADIACIÓN LÁSER: NO MIRE DIRECTAMENTE EL RAYO
RAYONNEMENT LASER – NE FIXEZ PAS DES
YEUX LE RAYON LASER
635nm, OUTPUT ≤ 1mW/CLASS II LASER PRODUCT
3.7V 500mAh Li-Polymer
COMPLIES WITH 21 CFR PARTS 1040.10 AND 1040.11
PRODUCTO LÁSER CON SALIDA ≤ 1mW.CLASE II, 635 nm,
3,7V 500mAh polímero de litio
CUMPLE CON LAS SECCIONES 21 CFR 1040.10 Y 1040.11
635 nm, SORTIE ≤ 1 mW/PRODUIT LASER DE CLASSE II
Pile au lithium-polymère de 3,7 V, 500 mAh
CONFORME AUX NORMES 21CFR ARTICLES 1040.10 ET 1040.11
CAUTION: Risk of fire and burns. Do not open, crush, heat above 100º C
(212º F) or incinerate.
PRECAUCIÓN : Riesgo de incendio y quemaduras. No abra, triture,
permita que esté a mayor temperatura que 100 ºC (212 ºF) ni incinere.
ATTENTION : Risque d'incendie et de brûlures. N'ouvrez pas le produit,
ne l'écrasez pas, ne le chauffez pas à plus de 100 ºC (212 ºF) et ne
l'incinérez pas.
MODES / MODOS/ MODES
DISTANCE AREA MEASURE
DISTANCE MEDIDA DEL ÁREA
DISTANCIA MESURE DE L'AIRE
LASER MEASURING TOOL
HERRAMIENTA DE MEDICIÓN CON LÁSER
OUTIL À MESURER AU LASER
Model / Modelo / Modèle: HLMT130
CAN ICES-3(B)/NMB-3(B)
Patent Pending/Patente en
trámite/Brevet en instance
MADE IN CHINA SERIAL NO.
HECHO EN CHINA SERIE NO.
FABRIQUÉ EN CHINE NUMÉRO DE SÉRIE
CONT. MEASUR
CONTINUACIÓN DE
LA MEDIDA
MESURE CONTINUE
1.85Wh
3