REVELL FORK LIFTER Manual Del Usuario página 7

3 INSerTINg BaTTerIeS
modell
3D Unscrew the screw of the cover by
turning it anticlockwise and remove
the lid.
3E Insert four AAA batteries. Please pay
attention to the polarity indication
(+ and -) visible in the battery
compartment.
3F Fit the cover again and screw in the
securing screw clockwise until
hand-tight.
5 STeerINg TrIM adjuSTMeNT
The correct trim is a basic requirement for fault-free driving behaviour from the
vehicle. Adjusting the trim is easy, but it requires a little patience and a feel for it.
Please follow the following instructions precisely:
if the vehicle pulls to the left or the right without being steered...
use the trim lever to correct the wheel alignment by turning it in the opposite
direction. The wheel alignment can be found on the bottom of the vehicle (cf. 5).
6 vehICle CoNTrol
6A In order to drive forwards, push the
lever for forward and reverse travel on
the left side of the remote control for-
wards.
6B In order to drive backwards, push the
lever for forward and reverse travel on the
left side of the remote control backwards.
The model stops instantly after the lever is
released.
12
4 STarT preparaTIoN
First move the switch on the front side of
the remote control to ON (4A) then set
the switch on the underside of the model
(4B) to ON. When switching off, always
switch off the vehicle first (cf.4B)! And
after it the remote control (cf.4A).
Otherwise, a drive command can acciden-
tally be triggered, causing the vehicle to
drive away on its own, which can lead to
considerable damage.
6C In order to drive along curves, push
the right lever for steering in the corres-
ponding direction.
6D The fork can be raised and lowered
with the luffing lever on the upper side
of the remote control. A soft clatter of the
slip clutch can be heard at the top and
bottom limit positiThis is completely
normal.
INSTruCTIoNS For SaFe drIvINg
gEnERAL DRiVing TipS:
• Always maintain visual contact with the vehicle and do not look at the remote control!
• On initial driving attempts, there is a general tendency toward excessive movements
of the controls. Make sure that you have sufficient room.
After a crash, always release the speed control immediately in order to prevent dama-
ge to the electronics.
ThE SuiTABLE DRiVing EnViROnmEnT:
The location in which the vehicle is driven should fulfill the following criteria:
1. It should be a location in which there is as much open area as possible, without
disruptive obstacles.
2. Make absolutely sure when starting that there are no people or animals in the
immediate vicinity.
3. Always watch the vehicle so that it does not drive into the operator, other people or
animals and injuries them.
TrouBleShooTINg
problem: The vehicle does not move.
Cause: • The batteries are too weak and/or depleted.
Remedy: • The batteries were possibly not inserted correctly. Please observe the polarity
indication in the model
• Please replace with new batteries.
problem: Remote control does not work.
Cause: • The remote control is switched off.
• The batteries were not inserted correctly.
• The batteries do not have enough power.
Remedy: • Repeat the switch-on process as described.
• Check whether the batteries are inserted correctly.
• Please replace with new batteries.
problem: The vehicle cannot be controlled with the remote control.
Cause: • The remote control is switched off
• The connection between the remote control and vehicle has been severed.
Remedy: • Move the remote control switch to the "ON" position.
• When the model is further than 5 metres away, move towards the model
Additional tips and trick can be found online at www.revellutions.de.
ServICe NoTeS
You can find ordering options, the online game and
useful information for all Revellutions models at
www.revellutions.de.
www.revellutions.de
13