Jasco myTouchSmart 41371 Manual De Instrucciones

Outdoor Digital
6-Outlet
Yard Stake Timer
Clock mode
indicator
Sensor
clock
my
on
Active program
indicator arrow 1
Indicates if program
2
is set
on
-6hr
Power
Setup
Note: If numbers are not visible on-screen, plug timer into an outlet
and charge for 30 minutes.
1. Connect the two segments of the stake, screw stake into the
bottom of the timer.
2. Select a sunny, outdoor location near a GFCI outlet. Light sensor
must have direct access to sunlight.
- If using sunset options, ensure the sensor is shielded from
nighttime light sources, such as flood lights.
3. Installation options:
- Firmly push the stake into the ground.
- Insert screws or nails into a solid surface leaving approximately
1/8in. exposed and hang the timer from the rear mounting
holes — stake can be removed.
4. The three outlets on the right of the timer can rotate to allow
side access.
5. Plug the cord directly into a GFCI outlet.
6. Ensure master shutoff switch is in the ON position ( )
— switch illuminates.
Bottom of stake timer
7. Open self-closing outlet cover.
8. Plug in device to be controlled.
9. If the device has a power switch, it must be in the ON position.
10. Repeat steps 7-9 for additional devices.
– DO NOT EXCEED ELECTRICAL RATINGS.
FCC Statement
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://goo.gl/j5bfYZ
Set mode
My on/my off times
indicator
Set custom ON/OFF times
set
my
my on my o
time 1 time 1
o
1
PM
my on my o
2
time 2
time 2
timer
to
reset Mode
AM/PM Reset button
indicator
Clears current time and all schedules
— resets timer to factory settings
Master shutoff
switch
Sensor
Power
Programming
1. Press the reset button with a toothpick or other nonmetal, fine-
tipped object — this also clears all programmed settings and
Sensor
clock set
restores factory defaults.
my
my
on o
1 1
PM
2 2
on timer
-6hr
to
reset
Power
2. Use the up and down arrow buttons to set the time — note
AM/PM indicator.
- Time can be adjusted when the clock is displayed — note
indicator arrow will move to set mode, and back to clock
when time is set.
Sensor
clock set
my
my
my on
o time 1
on
Up and down
1 1
PM
arrows
my on
2 2
Scroll to set and
time 2
schedule times
on
-6hr timer
to
reset
3. Press the mode button to select the desired operation —
Power
note indicator dot position above selected mode.
2nd my on/
- Timer (default) – Operates using the my on/my off settings.
my off times
- ON – All connected devices are powered.
- -6hr – Timer activates at sunset and remains on for 6
hours.
to
Sensor
-
clock set
my
my
my on
o time 1
on
1 1
PM
my on
2 2
time 2
on
-6hr timer
to
reset
Power
4. Create up to two custom my on and my off settings.
- With timer mode selected, press my on 1 button.
Sensor
clock set
my
my
on o
1 1
PM
2 2
on timer
-6hr
to
- Use the up and down arrow buttons to set the desired ON
reset
Power
time — indicator arrow appears on-screen next to my on 1
when setting is active. Default on setting is 5PM.
Sensor
clock set
my
my
my on
o time 1
on
1 1
PM
my on
2 2
time 2
on
-6hr timer
to
reset
- Press my off 1 button.
Power
- Use the up and down arrow buttons to set the desired OFF
time — indicator arrow appears on-screen next to my off 1
when setting is active. Default off setting is 12AM.
clock set
my
my
my on
o time 1
on
1 1
PM
my on
2 2
time 2
on
-6hr timer
to
- Repeat these steps to create a custom my on 2 and
reset
my off 2 time. Default on setting is 6PM. Default off setting
is 6AM.
RISK OF ELECTRIC SHOCK
• DO NOT EXCEED 15A CHRISTMAS/SEASONAL LIGHTING
• IF USING CHRISTMAS TREE OR DECORATIVE-LIGHTING PRODUCTS THAT ARE NOT MARKED WITH AN AMPERE RATING,
CONNECT NO MORE THAT 140 SCREW-BASE LAMPS (C7 OR C9) OR 12 STRINGS WITH PUSH-IN LAMPS TO THIS CORD SET
• IF USING AN OUTDOOR-USE CORD SET FOR AN EXTENDED PERIOD OF TIME (GREATER THAN 90 DAYS) PLEASE CONSIDER HARD
WIRING A PERMANENT OUTDOOR-USE RECEPTACLE RATED FOR YEAR-ROUND USE IN THE AREA THAT POWER IS NEEDED.
PLEASE CONTACT A LICENSED ELECTRICTION FOR PROPER INSTALLATION OF PERMANENT WIRING
• AFTER COMPLETION OF INSTALLATION, THE CONNECTOR SHALL BE MAINTAINED A MINIMUM OF 6 INCHES ABOVE GROUND.
• SUITABLE FOR INDOOR AND OUTDOOR LOCATIONS, STORE INDOORS WHILE NOT IN USE
RISK OF FIRE
• DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC.)
MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited
warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care
at 1-800-654-8483 between 7AM – 8PM CST.
my on my o
time 1 time 1
my on
my o
time 2 time 2
Mode
my o
time 1
my o
time 2
Mode
– Timer turns on at sunset and off at sunrise.
my o
time 1
my o
time 2
Mode
my on my o
time 1 time 1
my on my o
time 2 time 2
Mode
Sensor
my
on
my o
time 1
1
2
my o
time 2
on
Power
Mode
Sensor
my o
clock set
my
my
my on my o
time 1
on o time 1 time 1
1 1
PM
my o my on
my o
2 2
time 2 time 2
time 2
on timer
-6hr
to
reset Mode
Power
Mode
WARNING
clock set
my
my on my o
time 1 time 1
o
1
PM
my on my o
2
time 2
time 2
-6hr timer
to
reset
Mode
125V~60Hz
Maximum load:
15A
Suitable for indoor and
outside use.
Works with LED, CFL,
incandescent and halogen
bulbs.
41371 v1 06/07/19