Jasco UltraPro 49789 Manual De Instrucciones

49789 & 49790
PLUG-IN SINGLE-OUTLET
DIGITAL TIMER
SETUP
1. If numbers are difficult to read or not visible
on-screen, plug timer into an outlet and let timer
charge for 1 hour. Once charged, press the reset
( ) button in the lower right corner using a
toothpick or pencil.
Note: After timer is charged, it can be removed
from the outlet for easy programming. Return to
outlet when finished.
Note: When timer is reset, the time will flash.
2. Use up ( ) and down ( ) arrows to set
current time. Take note of the AM/PM setting.
PROGRAMMING OPTIONS
DEFAULT TIMER
There are two ON/OFF times available
with preset default times. To activate
default times, simply press ON TIME or
OFF TIME button so the arrow ( ) next
to the button is visible on the display. To
deactivate the default timer, press and
release the button. The arrow next to the
button will disappear.
CUSTOMIZED TIMER
On time: Press and release either ON TIME button to
enter custom setting mode. The default on time
flashes. Use arrow buttons ( ) to set the desired
on time. Press the ON TIME button or wait 5 seconds
to set. If no button is pressed within 5 seconds, the
default timer will be set and the display will return to
clock mode. If you set the on time earlier than the
current time, it will not turn on until the next day at
the scheduled time.
Note: Mode indicator ( ) will move under SET while
programming, then back to CLOCK if it times out or
after on time is set.
Off time: Press and release either OFF TIME button to
enter custom setting mode. The default off time
flashes. Use arrow buttons ( ) to set the desired
off time. If no button is pressed within 5 seconds, the
default timer will be set and the display will return to
clock mode. Press the OFF TIME button or wait 5
seconds to set.
Note: When an on time or off time is set, the active
program indicator ( or ) will appear on the screen
beside the button. Programs may run individually or
simultaneously.
ON/OFF OVERRIDE BUTTON/DOOR
Using ON/OFF override with no scheduled programs:
- If the timer is off, press & release the ON/OFF
override to turn the timer on.
- If the timer is on, press & release the ON/OFF
override to turn the timer off.
Using the ON/OFF override with scheduled programs:
- If a scheduled program is running and the timer is on, press & release the ON/OFF override
to turn the timer off. It will remain off until the next scheduled program turns the timer on.
- If a scheduled program is running and the timer is off, press & release the ON/OFF override
to turn the timer on. It will remain on until the next scheduled program turns the timer off.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/49789i
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
R
ON/OFF
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
ON/OFF
CLOCK SET
ON TIME 1 ON TIME 2
ON ON
5:00PM
TIME TIME 6:00PM
AM
OFF TIME 1 OFF TIME 2
OFF OFF
12:00AM 6:00AM
TIME TIME
R
ON/OFF
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
ON/OFF
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
ON/OFF
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
ON/OFF
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
ON/OFF
CLOCK SET
ON ON
TIME TIME
AM
OFF OFF
TIME TIME
ON/OFF
FCC/IC - EN
Supplier Declaration of Conformity | Model #: 49789, 49790 | Jasco Products Co.,
10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
SPECIFICATIONS
125VAC, 60Hz
15A 1875W general/resistive
5A 625W tungsten
1/2HP motor
Works with dimmable LED and CFL bulbs
RESET
BUTTON
R
R
R
WARNING
RISK OF ELECTRICAL SHOCK
• PLUG DIRECTLY INTO AN
ELECTRICAL OUTLET
R
• DO NOT USE IN WET
LOCATIONS
• USE INDOORS ONLY
• UNPLUG TIMER BEFORE
CLEANING
R
R
MADE IN CHINA/HECHO EN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 2-year limited warranty. Visit www.byjasco.com for
warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between
7AM-8PM M-F, Central Time.
©JASCO 2020 | 49789, 49790 | 09/03/20 v1
RISK OF FIRE
• DO NOT USE TO CONTROL
APPLIANCES THAT CONTAIN
HEATING ELEMENTS
(COOKING APPLIANCES,
HEATERS, IRONS, ETC.)
• DO NOT EXCEED
ELECTRICAL RATINGS