Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

EN
GOLIATH RACE
USER'S MANUAL
2
1
1
GOLIATH 360º BASIC CLAMP
2
CLAMP PRESSURE
3
SIDE LOOP
4
UP/DOWN LOCK
YOU WILL FIND IN THE BOX:
1 GOLIATH G2-RACE support body folded
1 clamp 360º BASIC
1 Handle to attach the clamp
TECHNICAL DESCRIPTION:
Support with manual height adjustment and folding legs
Manual raising and lowering control - Manual opening of the legs with clip fasteners
Minimum height of the clamp: 700mm
Maximum height of the clamp: 1.300mm
Maximum weight to be supported: 30kgs
G2-RACE
ASSEMBLY INSTRUCTIONS:
MOUNTING THE CLAMP ON THE STAND:
1- Remove the washer from the rear of the clamp by unscrewing the Allen screw, insert the
rear of the clamp into the clamp holder. (Photo 1)
2- Mount the side loop [3] on the right side of the clamp holder and x the clamp with it so
that it does not rotate.
3
3- Replace the washer on the back of the clamp and x the Allen screw to prevent the
clamp from accidentally falling. (Photo 2)
Now you have the clamp mounted, the clamp should roll freely once the side handle [3] of
4
the clamp holder is loosened and remain xed with the tightening of the clamp holder.
INSTALLATION OF THE STAND:
1- Unfold the legs by removing the clip fasteners from each leg. (Photo 4)
2- Once the legs are unfolded, put the clip fasteners back in their respective holes, this will
prevent the stand from accidentally folding.
3- Check if the legs of the support adapt to the ground or oor on which you are going to
work. In case of a limp, adjust the legs on the lower part with the regulating blocks to
compensate the height. (Photo 3)
* This system of legs with conical opening has an automatic adaptability to the ground to
avoid limping, as long as this unevenness does not exceed 6 mm approximately.
WWW.GOLIATH-BIKE.COM
Photo 3
Photo 1
Photo 2
Photo 4

Publicidad

loading

Resumen de contenidos para goliath RACE

  • Página 1 * This system of legs with conical opening has an automatic adaptability to the ground to avoid limping, as long as this unevenness does not exceed 6 mm approximately. YOU WILL FIND IN THE BOX: 1 GOLIATH G2-RACE support body folded 1 clamp 360º BASIC 1 Handle to attach the clamp...
  • Página 2 MAINTENANCE: *For this type of frame there is a special clamp (GOLIATH 360º CARBON) that allows to cover more frame surface and reduce the e ort per square centimeter, it also has a softer polyurethane 1 - The bracket does not require any speci c maintenance.
  • Página 3 * Este sistema de patas con abertura cónica tiene una adaptabilidad al terreno automática para evitar cojeo, siempre y cuando este desnivel no supere 6 mm aproximadamente. QUE ENCONTRARÁS EN LA CAJA: 1 Cuerpo de soporte GOLIATH G2-RACE plegado 1 Pinza 360º BASIC 1 Maneta para jar la pinza DESCRIPCIÓN Y CARACTERÍSTICAS TÉCNICAS:...
  • Página 4: Mantenimiento

    2- El fabricante no se hace responsable de cualquier modi cación realizada sin la autorización previa del mismo. 3- Sólo utilizar el soporte GOLIATH G2-RACE según las indicaciones del manual de instrucciones del fabricante. 5 - La pinza no tiene tope de apriete [2], el usuario debe determinar la presión que necesita 4- Sólo realizar mantenimiento y reparaciones según las indicaciones del manual de instrucciones del fabricante.
  • Página 5 *Ce système de pieds à ouverture conique a une adaptabilité automatique au sol pour éviter de boiter, tant que cette inégalité ne dépasse pas 6 mm environ. QUE VOUS TROUVEREZ DANS LA BOÎTE: 1 corps de soutien plié GOLIATH G2-RACE 1 pince BASIC à 360 1 Poignée pour xer la pince DESCRIPTION ET CARACTÉRISTIQUES TECHNIQUES :...
  • Página 6 Il est important de connaître le type de cadre à serrer, car les cadres en carbone sont plus faibles au serrage. *Pour ce type de cadre, il existe une pince spéciale (GOLIATH 360º CARBON) qui permet de couvrir une MAINTENANCE : plus grande surface du cadre et de réduire l'e ort par centimètre carré, elle possède également une...

Este manual también es adecuado para:

G2-race