Cree XSP Serie Instrucciones De Instalación

IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l'alimentation avant l'installation.
2. This luminaire must be installed in accordance with the NEC or your local
electrical code. If you are not familiar with these codes and requirements,
consult a qualified electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique
local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez
contacter un électricien qualifié.
3. If NEMA photo control is installed refer to NEMA
®
instructions.
4. If mounting bolts are completely removed in the field they should be hand
threaded (prior to use of power tools) to ensure proper engagement of the
thread when re-installing. Failure to pre-start threads may result in cross-
threading or stripping of the bolts during reinstallation.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
TO INSTALL:
1
Splashguard
LUMINAIRE INSTALLATION
STEP 1:
DO NOT remove splashguard from fixture.
If mounting fixture to 1.25 IP pipe (1.66 O.D.),
there is no need to modify the splashguard. If
mounting fixture onto 2.0 IP pipe (2.38 O.D.),
remove the knockout of the splashguard thru
the rear opening of the fixture while the fixture
is closed. See Figure 1.
STEP 2:
To open cover, hold fixture and loosen the
captive D-ring and allow the cover to swing
open. Splashguard may dislodge from fixture,
but should be repositioned once ready to
mount. See Figure 1.
1 of 2
Receptacle section for
®
2 4 point
Mounting
Bracket
(Optional)
Mounting
Pole Adjustment
Bracket
Steps
Mounting Bracket Mounting Bracket
Bolts Bolts
STEP 3:
Slide fixture on to pole through opening on the
rear of housing and through splashguard. See
Figure 2.
STEP 4:
To level fixture, use bubble level located inside
housing. Adjust leveling of fixture from side
to side. To level from front to back, slide pole
to different step in upper housing. Each step
changes the angle in 2.5° degree increments.
See Figure 2.
STEP 5:
Once desired position is achieved, tighten
mounting bolts to the appropriate torque
values specified in TORQUE VALUES table to
above. See Figure 2 (use 9/16" socket wrench).
LED Street and Area Light
Includes: XSPMD and XSPLG Luminaires
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D'INSTALLATION
• Prior to installation, store luminaire in a dry location
protected from rain, dust, and outdoor environment. If
equipped with a photocell receptacle, do not store or install
luminaire outdoors without immediately installing a suitable
photocell, shorting cap, or other compatible device. Do
NOT leave receptacle open to environmental elements.
Luminaires with a top-mounted photocell receptacle should
not be installed in an up-light position or at a tilt greater
than 45 degrees from the down-light position.
TORQUE VALUES
Pipe
Pipe Position
Size
+5.0 degrees tilt
+2.5 degrees tilt
1.66 in
0 degrees (no tilt)
O.D.
-2.5 degrees tilt
-5.0 degrees tilt
+5.0 degrees tilt
+2.5 degrees tilt
2.38 in
0 degrees (no tilt)
O.D.
-2.5 degrees tilt
-5.0 degrees tilt
NOTE: Luminaires with 4 point mount will have
(2) mounting brackets and (4) mounting bolts.
See Figure 2.
STEP 6:
IMPORTANT - DO NOT exceed these torque
levels on the mount bolts. Exceeding
recommended torque value resulting in
excessive deformation of mounting bracket
will cause stripping of mount hardware which
could lead to an unsafe mounting condition.
STEP 7:
Reference Electrical Connections section for
completing electrical connections.
XSP Series
Bolt Torque Bolt Torque
Required Required
(in-lbs) (N-m)
200 22
200 22
200 22
200 22
200 22
200 22
200 22
200 22
200 22
200 22
CI379X23R0