Rules For Safe Operation; Other Safety Warnings; While Operating - Bolens BL50 Manual De Instrucciones

• This tool is double-insulated. Use only identical replacement
parts when servicing. Repair or replace damaged cords.
WARNING: To reduce the risk of electrical shock,
use only SW-A, SOW-A, STW-A, STOW-A, SJW-A,
SJOW-A, SJTW-W or SJTOW-A cord types.
• To reduce the risk of electrical shock, this unit has a polar-
ized plug (one blade is wider than the other). This unit will
fit with a polarized plug in one way only. If the plug does
not fit fully into the unit, reverse the plug. If it still does not
fit, use a cord with the correct connection. Do not modify
the unit in any way.
MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR 120
VOLT APPLIANCES USING 0-6 AMPS
Cord length (ft.) 25
Wire size (AWG) 16
• CORD SETS: Make sure your cord set is in good condition,
with a cord that is heavy enough to carry the current that
your unit will draw. An undersized cord set will cause a
drop in line voltage resulting in a loss of power, as well as
overheating. The table shown above illustrates the correct
size to use depending on the cord length and nameplate
amperage rating. If in doubt, use the next heavier size line
gauge. The smaller the gauge number, the heavier the
cord. To prevent the cord from disconnecting from the
unit, use the cord hook shown in the Operating Instructions.
• Do not abuse the power cord. Do not pull or carry the unit
by the cord, use the cord as a handle, close a door on the
cord, or pull the cord around sharp edges or corners. Keep
the cord away from heated surfaces, oil and sharp edges.
• Ground Fault Circuit Interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) that will be used
for the unit. Use receptacles with built-in GFCI protection
for an extra measure of safety.
• A nameplate on your unit indicates the voltage used. Never
connect the unit to an AC voltage that differs from this
voltage.
• Avoid dangerous environments. Never operate your unit in
damp or wet conditions. Moisture is a shock hazard.
• Inspect all extension cords and the unit power connection
periodically. Look closely for deterioration, cuts or cracks in
the insulation. Also inspect the connections for damage.
Repair or replace the cords if any defects appear.
• Do not use the unit in the rain.
• Do not handle the plug or the unit with wet hands.

WHILE OPERATING

• Wear safety glasses or goggles that meet ANSI Z87.1 stan-
dards and are marked as such. Wear ear/hearing protection
when operating this unit. Wear a face or dust mask if the
operation is dusty.
• Wear heavy long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants, san-
dals or go barefoot. Secure hair above shoulder level.

RULES FOR SAFE OPERATION

50 100 150
16 16 14
• The cutting attachment shield must always be in place while
operating the unit. Do not operate unit without both trim-
ming lines extended, and the proper line installed. Do not
extend the trimming line beyond the length of the shield.
• Adjust the D-handle to your size to provide the best grip.
• Be sure the cutting attachment is not in contact with any-
thing before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Do not carry around a unit that is
plugged in with your finger on the trigger switch. Be sure
the switch is in the off position when plugging in the unit.
• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving
parts. Do not touch or try to stop the cutting attachment
when it rotates.
• Always stop the motor when cutting is delayed or when
walking from one cutting location to another.
• If you strike or become entangled with a foreign object,
stop the motor immediately and check for damage. Do not
operate before repairing damage. Do not operate the unit
with loose or damaged parts.
• Stop the unit and unplug it for maintenance or repair.
• Use only genuine original equipment replacement parts
and accessories for this unit. These are available from your
authorized service dealer. Use of any non-original parts or
accessories could lead to serious injury to the user, or dam-
age to the unit, and void your warranty.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.

OTHER SAFETY WARNINGS

• Disconnect the unit from the power supply when it is idle,
when you are storing or transporting it, when you are ser-
vicing it, and when you are changing attachments.
• Store the unit in a dry area, locked up to prevent unautho-
rized use or damage, and stored in a high place out of the
reach of children.
• Never douse or squirt the unit with water or any other liq-
uid. Keep handles dry, clean and free from debris. Clean
after each use. See the Cleaning and Storage instructions.
• Keep these instructions. Refer to them often and use them
to instruct other users. If you loan someone this unit, also
loan them these instructions.
SAVE THESE INSTRUCTIONS
4