Cequent Performance Products 75186 Instrucciones De Instalación

Equipment Required:
Fastener Kit: F75186
Wrenches: 3/4"
Drill Bits: 1/2"
Bumper
bracket
Note:
Fasteners typical, both sides
WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY
OCCUR DUE TO OVER TIGHTENING.
WARNING: DO NOT DRILL OR WELD TO THIS HITCH. WARNING: DO NOT DRILL OR WELD TO THIS HITCH
1
Qty. (4) Carriage Bolt 1/2-13 X 2.00
2
Qty. (2) Block .25 X 1.00 X 2.00
3
Qty. (8) Lock Washer 1/2"
4
Qty. (8) Hex Nut 1/2-13
MODELS WITH 75" BED USE THIS DIAGRAM (See second page for models with 56" bed ) MODELS WITH 75 BED USE THIS DIAGRAM (See second page for models with 56 bed.)
1. Remove the bolt from the bottom of the frame on both sides of the vehicle. Insert 1/2" carriage bolt
and large bolt plate through large rear hole in the frame. Repeat for the other side.
2. Lift the hitch up to frame with the carriage bolts going down through the second hole from the forward end of hitch bracket. Install 1/2" lock
washers and nuts on the bolts. See Diagram. Hand tighten fasteners.
3. Attach the "L" brackets to hitch brackets using the 1/2" carriage bolts with small bolt plates and the 1/2" hex bolts with 1/2" conical washers
into the "L" brackets as shown. Hold the hitch level. Using one of the obround holes in the "L" bracket as a guide drill a 1/2" hole into the
bumper bracket. Install 1/2" hex bolt, serrated washer, lock washer, and nut. (Both sides)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2002, 2003, 2004, 2006, 2008, 2009, 2011 Cequent Performance Products
Installation Instructions
1
5
4 3
3
4
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Nissan Pick-Up
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU4
USE ONLY TOWING PRODUCTS SUPPLIED OR APPROVED BOLTS, USE ONLY TOWING PRODUCTS SUPPLIED OR APPROVED BOLTS
LOCKNUTS, AND WASHERS TO INSTALL THIS HITCH
1
2
6 7
"L" Bracket
5
Qty. (2) Block .25 X 1.500 X 3.00
6
Qty. (4) Bolt 1/2-13 X 1.25
7
Qty. (4) Conical Washer 1/2"
8
Qty. (2) "L" Bracket
Sheet 1 of 6
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5000 (2270 Kg)
4000 (1816 Kg)
IMPORTANT NOTES
1
Frame
5
Drilled hole
3
4
N75186 4-18-11
Form: F205 Rev A 5-6-05
75186
44148
87491
78273
U-HAUL
Max Tongue
WT (LB)
550 (250 Kg)
400 (182 Kg)
Rev. K