Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards.
Obey all safety messages following these symbols.
m
WARNING
avoid possible
injury or death
FOR YOUR SAFETY READ ALL INSTRUCTIONS
BEFORE INSTALLATION AND OPERATION
Installer:
Provide these instructions to the consumer.
Consumer:
Keep documents for future reference.
The Atwood Power Jack is a 12-volt DC motor driven screw jack intended for use
on recreational type and marine trailers. Patent # D349800. Jack is used to level
trailer or raise and lower coupler for hookup to tow vehicle.
m
PERSONAL INJURY/PROPERTY DAMAGE
• Retract jack fully before towing.
• Do not use blocks to increase height of jack.
• Use 4000 lb. Heavy Duty Power Jack if you use equalizer bars between the trailer and the tow
vehicle.
deluxe
Max. Lifting Cap.
3000
lbs
INSTALLATION
1.
Block tires of trailer and securely support trailer tongue.
2.
The Atwood RV Power Jack is designed to attach to the top surface of
an A-frame type tongue having mounting holes typical of the Atwood
A-frame couplers FIG 1. Use coupler installation instructions (MPD
87984) if installing coupler. The Marine Power Jack attaches to the side
of a straight tongue trailer.
3.
A lower support plate must be used for side support of the RV jack on
the lower surface of the A-frame FIG 1.
HOLE DIAMETERS:
Hole in lower support plate must align with hole in coupler.
TO ORDER LOWER SUPPORT PLATE:
Using a 1/8˝ fillet weld, No. E6011 AWS welding rod 1/8˝ diameter,
machine amps (AC or DCRP) at 160-180 with 50 volts, weld plate full
length on each side to underside of A-frame. The maximum frame
height is 6 inches.
4.
Place RV jack through holes in coupler and lower support plate, FIG 1-A.
Attach with three (3) bolts (3/8˝ dia. x 5/8˝ long, grade 5, FIG 1-B. NOTE:
Torque bolts to 15 foot lbs. minimum /20 foot lbs. max.
Note: There must be metal to metal contact between jack and coupler. The three mounting
bolts with attached star washers must be used. The star washers are designed to remove
paint on the surface of jack flange. The bolts also should remove paint from the mounting
holes in coupler. If a grounding problem occurs (i.e. no power) check these two surfaces to
be sure there is metal to metal contact between jack and coupler. For wiring, see WIRING
ILLUSTRATIONS
2 & 3.
FIG
5.
Attach jack as shown.
m
CAUTION
avoid possible
injury or death
CAUTION
heavy duty
marine
4000
1000
Light Weight -
2.02˝
(MIN)
Deluxe / Heavy Duty -
2.20˝
Light Weight -
Atwood MPD 80263
Deluxe / Heavy Duty -
Atwood MPD 80570
6.
Route wire lead from motor along trailer tongue to battery. Secure lead
to jack housing and trailer frame using cable ties or equivalent.
7.
Remove fuse from fuse holder. Connect the wire lead from the jack
directly to the positive (+) terminal of the battery. Replace the fuse into
the fuse holder. For auxiliary battery, connect lead to auxiliary battery
positive (+) terminal so that jack may be used when connected to 115v.
For additional wire, use #10 stranded copper wire or larger.
8.
After reinstalling fuse, check installation by pressing switch marked "EXT"
for jack extension or "RET" to retract the jack.
9.
On all power jacks, check utility light by moving switch to "ON" or "OFF".
• Hold Robofoot below the clevis pin parts when installing. This is a moving part and is a potential
pinch point.
10. The Power Jack may come packaged with the Atwood Robofoot.
Instructions for installation, operation and maintenance of the Atwood
Robofoot are included with the Robofoot. The Robofoot should be
installed after the jack is securely attached to the coupler.
1.
To raise or lower jack, press switch marked "EXT" or "RET". "Extend" and "Retract"
refer to the jack, not the trailer.
2.
Release switch when jack nears full retraction or full extension to prevent
unnecessary wear on motor clutch.
a. When jack reaches its maximum extended or retracted length or maximum
load, a clicking noise will be heard. This is the overriding clutch built into the
motor to prevent overload.
Release switch immediately when clicking is heard. If the jack has been over
extended or retracted, it may bind. If so, operate with the manual override
handle, per STEP 3 below, to release it from the bind.
b. When the heavy duty power jack is being retracted, there may be some
audible noise, coming from the brake area. This is normal and is due to the
high load for which this jack is rated.
3.
In case of electrical failure- raise or lower jack as follows:
MANUAL OPERATION FOR ALL VALUE & PERFORMANCE POWER JACKS
2.09˝
a. Attach the Drill Crank adapter part #85385 to a powered drill. An optional
(MAX)
manual drive handle, part # 87891 (not included) (FIG 1-C) can also be used to
2.28˝
manually raise and lower the jack
b. Insert the included Drill Crank Adapter into the manual override access port
to engage manual override pin.
c. Activate drill or rotate handle (if using the manual drive handle) clockwise to
raise the jack and counter clockwise to lower the jack.
1.
Before each use, inspect jack tubes and replace if bent or damaged.
2.
If wiring is connected to battery terminal, inspect at least twice each year for
corrosion. Clean with a solution of baking soda and water, and then apply a
thin coat of grease. NOTE: The motor ground screw (FIG 1-D) and mounting
bolts (FIG 1-B) must be cleaned too if a ground continuity problem occurs.
3.
Once each year, extend jack as far as possible and clean inner ram tube.
Coat tube with light coat of silicone spray lubricant. The Electric Drive
Motor Landing Leg system is protected by a 30 amp fuse. If replacement is
necessary, replace only with a Buss Type AGC-30 fuse or equivalent, available
in automotive supply stores.
4.
The Robofoot does not need to be lubricated or modified after installation.
1
DOCUMENT PART NUMBER 88320
POWER JACK
RV and Marine Applications
•Installation •Operation •Maintenance
m
CAUTION
HAND OR FINGER INJURY
OPERATION
MAINTENANCE
Effective 2/21/14

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Lippert Components deluxe 3000

  • Página 1 DOCUMENT PART NUMBER 88320 POWER JACK RV and Marine Applications •Installation •Operation •Maintenance Effective 2/21/14 Route wire lead from motor along trailer tongue to battery. Secure lead SAFETY ALERT SYMBOLS to jack housing and trailer frame using cable ties or equivalent. Safety Symbols alerting you to potential personal safety hazards.
  • Página 2: Troubleshooting Guide

    Power Jack TROUBLE SHOOTING GUIDE Effective: 2/21/14 Guides are only intended for use on Atwood® products by service technicians M O T O R C L U T C H E N G A G E S who have successfully completed Atwood® training. This guide should be used in conjunction with the appropriate Instruction Manual provided with the product Normal if jack leg is at fully retracted ......None, but let go of switch when you hear the clutch and any applicable industry standards.
  • Página 3: Replacement Service Parts

    REPLACEMENT SERVICE PARTS 3K AND 4K POWER JACK ITEM 3K SHORT 3K STANDARD 4K STANDARD MARINE DESCRIPTION 80938/9 80938/9 80938/9 80938/9 Upper Cover (White/Black) 87057 87057 87057 87057 Cover Screw 87942 87942 87942 87942 Motor Ground Screw 86111 86111 86111 86111 Lock Washer 75625...
  • Página 4 POWER JACK WIRING ILLUSTRATIONS BLACK WIRE FROM LED BASE WHITE WIRE FROM LED BASE BLACK FUSE WIRE W/RED JUMPER BLACK GROUND WIRE W/BLACK JUMPER RED JUMPER FROM FUSE WIRE GROUND TO MOTOR SCREW AT ASSEMBLY MARINE POWER JACKWIRING ILLUSTRATIONS BLACK WIRE FROM LED BASE WHITE WIRE FROM LED BASE...
  • Página 5 NUMÉRO DE PIÈCE DU DOCUMENT : 88320 VÉRIN MOTORISÉ Applications pour VR et marine •Installation •Fonctionnment •Entretien Entrée en vigueur : le 21 février 2014 de montage dotés de rondelles éventails doivent être utilisés. Les rondelles éventails sont SYMBOLES D’ALERTE DE SÉCURITÉ conçues pour enlever la peinture sur la surface de la collerette du vérin.
  • Página 6: Guide De Dépannage

    Vérin motorisé GUIDE DE DÉPANN AGE Entrée en vigueur : le 21 février 2014 surpassement manuel pour engager la tige de surpassement manuel. M A U V A I S E M I S E À L A T E R R E c.
  • Página 7: Pièces De Rechange

    PIÈCES DE RECHANGE VÉRIN MOTORISÉ 3K ET 4K ARTICLE 3K COURT 3K STANDARD 4K STANDARD MARINE DESCRIPTION 80938/9 80938/9 80938/9 80938/9 Couvercle supérieur (blanc/noir) 87057 87057 87057 87057 Vis du couvercle 87942 87942 87942 87942 Vis de mise à la masse du moteur 86111 86111 86111...
  • Página 8 SCHÉMAS DE CÂBLAGE DU VÉRIN MOTORISÉ FIL NOIR DE LA BASE DE LA DEL FIL BLANC DE LA BASE DE LA DEL FIL NOIR DU FUSIBLE AVEC CAVALIER ROUGE FIL NOIR DE MISE À LA MASSE AVEC CAVALIER NOIR CAVALIER ROUGE DU FIL DU FUSIBLE VIS DE MASSE VERS LE MOTEUR...
  • Página 9: Gato Potente

    DOCUMENTO DE PARTE NÚMERO 88320 GATO POTENTE Aplicaciones RV y Marinas •Instalación •Operación •Mantenimiento Efectivo: 2/21/14 a la batería. Asegurar los cables a la cubierta del gato y a la estructura del SÍMBOLOS DE ADVERTENCIA DE SEGURIDAD remolque usando precintos plásticos o algo equivalente. Símbolos de seguridad lo alertan de peligros potenciales personales.
  • Página 10: Guía De Solucíon De Problemas

    GATO POTENTE GUÍA DE SOLUCÍON DE PROBLEMAS Efectivo: 2/21/14 Las guías son solo destinadas a ser usadas para productos Atwood® por el servicio S E E N G A N C H A M O T O R D E E M B R A G U E de técnicos quienes han exitosamente completado el entrenamiento Atwood®.
  • Página 11 SERVICIO PARTES REEMPLAZABLES 3K Y 4K GATO POTENTE ARTÍCULO 3K CORTO MARINO DESCRIPCIÓN ESTÁNDAR ESTÁNDAR 80938/9 80938/9 80938/9 80938/9 Covertor Superior (Blanco/Negro) 87057 87057 87057 87057 Tornillo Del Covertor 87942 87942 87942 87942 Tornillo De Conexión A Tierra Del Motor 86111 86111 86111...
  • Página 12 POWER JACK WIRING ILLUSTRATIONS BLACK WIRE FROM CABLE NEGRO DE BASE LED LED BASE WHITE WIRE FROM CABLE BLANCO ENSAMBLAJE DE CABLE FUSIBLE LED BASE DE BASE LED NEGRO CON CABLE PUENTE ROJO BLACK FUSE WIRE W/RED JUMPER BLACK GROUND WIRE CABLE NEGRO DE W/BLACK JUMPER CONEXIÓN A TIERRA CON...

Este manual también es adecuado para:

Heavy duty 4000Marine 1000

Tabla de contenido