Cequent Performance Products 75896 Instrucciones De Instalación

Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75896F
Wrenches: 10mm, 17mm, 19mm, small
screwdriver, Phillips head screwdriver, &
6" socket extension
Reuse Existing M8
Bolts
Note: When stowing the spare
or flat tire, it may be necessary
to lift up on the rear edge of
the tire to clear hitch.
j
Hex Bolt – M12 x 1.25 x 30mm CL8.8
Qty. (6)
l
Qty. (2) Washer Conical 3/8
n
Qty. (2) Bolt M8 x 1.25 x 30 CL8.8
If present, remove plastic appearance panels which cover driver's and/or passenger's side frame rails. Remove the plastic
1.
rivets that fasten the fascia tabs to the appearance panel. Note: Remove the center of the rivet with a small screwdriver.
Passenger's side panel can be reinstalled. Return drivers' side panel and fasteners to owner.
2. Remove tow hooks from each frame rail and return hooks and fasteners to vehicle owner.
3. Remove plastic and rubber plugs from bottom of frame rail. Return to owner.
4. Remove existing M8 bolts from exhaust hanger bracket. Install exhaust bracket (item 6) on frame rail using existing M8 bolts.
Use M8-1.25 bolts to install exhaust hanger bracket to exhaust bracket.
5. Be careful not to pinch hoses on the outside of the passenger side frame rail or scratch fascia. Remove excess caulking from
rails if needed.
6. Align hitch into position over existing weldnuts as shown and install fasteners to bottom of frame rails.
Note: Existing fascia tab should be reinstalled between frame rail and bracket.
7. Torque all fasteners to specifications.
8. Reinstall passenger side appearance panel.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2014 Cequent Performance Products, Inc. Printed in Mexico
Installation Instructions
Toyota Highlander
Fascia
l m
o
Exhaust hanger
bracket
n
Existing fascia tab
Existing weldnuts in
both vehicle frame
k
j
Tighten all M12 x 1.25 CL8.8 fasteners with torque wrench to 76 Lb.-Ft. (103 N*M)
Tighten all M8 x 1.25 CL8.8 fasteners to 20 Lb.-Ft. (27 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, 4
Frame rail
k
j
k
Conical Toothed Washer – 1/2"
Qty. (6)
m
Qty. (2) Nut, M8 x 1.25
o
Qty. (1) Exhaust Bracket
Sheet 1 of 3 75896N
Part Numbers:
75896
87660
44710
Max Gross Max Tongue
Trailer WT (LB) WT (LB)
8000 (3632 Kg) 900 (409 Kg)
6000 (2724 Kg) 900 (409 Kg)
Accessory Rating
Vehicles
heating/cooling
hoses located in
this area.
Use caution not to
pinch.
3/12/14 Rev. A
Form: F205 Rev A 5-6-05
C