Cequent Performance Products 75051 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 01130-584
Wrenches: 18mm, ¾, 7/8
Drill Bits: None
Attachment Hole for
Short Bed Models
Attachment hole for
Long Bed Models
nkm
lkj
j
Qty. (6) Hex Bolt M12 x 1.75 x 45mm CL10.9
k
Lock Washer – ½"
Qty. (8)
l
Qty. (6) Hex Nut M12 x 1.75
1. Remove bumper, leaving brackets attached to frame. Disconnect bumper wiring before removing bumper.
Note: Pre-1994 Models: Bumper is attached to bumper brackets by two (2) horizontal bolts.
1994-Present Models: Bumper is attached to bumper brackets by two (2) vertical bolts, see Figure 2.
2. Remove bumper brackets from frame. Remove bumper wiring guides from bumper brackets.
Mark spare tire carrier 1/8" inboard of outboard edge of frame.
3.
4. Lower spare tire and cut off carrier along line marked.
Note: Steps 3 & 4 not required for later model vehicles using a cable storage system for spare tire.
5. Position receiver on frame and loosely re-install bumper brackets using (3) M12 bolts and fasteners per side. Receiver brackets are sandwiched between bumper
and frame.
Pre-1994 Models: Re-install bumper on bumper brackets with original bolts, using three (3) ½" washers at each bolt location as spacers between brackets and
6.
bumper, see Figure 1.
` 1994-Present Models: Re-install bumper on bumper brackets with original bolts. Slots in bumper bracket allow for adjustment.
7. Tighten all bolts with torque wrench to 75 Lb.-Ft. (102 N*M)
8. Raise spare tire back into position and secure. Re-connect bumper wiring
Vehicles without bumpers: Substitute six (6) ½" conical toothed washers (not provided) for lock washers used with the M12 bolts.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
2002, 2009, 2011, 2014 Cequent Performance Products – Printed in Mexico
©
Installation Instructions
Chevrolet S-10 Pickup
GMC S-15 Pickup/Sonoma Pickup
Isuzu Hombre
Vehicle Step
Bumper
Frame
Bumper Bracket
Figure 1
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all M12 x 1.75 CL10.9 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Pre-1994 Models:
Place (3) ½" washers
(Item 6) At each attachment
Between bumper and
Bumper brackets
Fasteners Typical
Both Sides
1994-Present Models
Bumper Bracket Configuration
m
Qty. (2) Hex Bolt ½-13 x 1-1/2 GR5
n
Qty. (2) Hex Nut ½-13
o
Flat Washer – ½"
Qty. (12)
Sheet 1 of 3
Part Numbers:
75051
44732
75881
Max Gross Max Tongue
Trailer WT (LB)
6000 (2724 Kg.) 750 (340.5 Kg.)
3500 (1589 Kg.) 350 (159 Kg.)
Accessory Rating
Bumper Bracket
Bumper Bracket
Bolts
Bumper
Bolts
Figure 2
Typ. Both Sides
N75051 5-20-14
Form: F205 Rev A 5-6-05
U-Haul
WT (LB)
C
Rev. C