Tabla de contenido
Publicidad
CD Player
•
CD-RWs, MP3 CD-ROMs, CD-I, CDV,VCD,
DVD or computer CDs are not possible for
playback on this set.
1 Adjust the source selector to CD.
2 Insert a CD/ CD-R with the printed side fac-
ing up and press the CD door gently close.
3 Press PLAY/PAUSE 2; on the set to start
playback.
4 To pause playback press PLAY/PAUSE 2;.
Press PLAY/PAUSE 2; again to resume
play.
5 To stop CD play, press STOP 9.
6 To switch off the set, adjust the source
selector to TAPE/
position and
POWER OFF
check the cassette keys are released.
Note : CD play will also stop when:
- you open the CD compartment;
- you select TUNER or TAPE/
POWER OFF
sound source;
- the CD has reached the end of playback.
Selecting a different track
During playback you can use ∞ / § to select
a particular track.
- If you have selected a track number in the stop
or pause position, press PLAY/PAUSE 2; to
start playback.
Press § once briefly for the next track, or
•
press repeatedly until the desired track num-
ber appears in the display.
Press ∞ once briefly to return to the begin-
•
ning of a current track.
Press ∞ repeatedly for a previous track.
•
Finding a passage within a
track
1 During playback, press and hold down ∞ /
§.
•
The CD is played at high speed and low vol-
ume.
2 When you recognize the passage you want
release ∞ / §.
•
Normal playback resumes.
Note : When searching within a final track
and you reach the end of the last track, the
CD goes to stop mode.
Programming track
numbers
You may store up to 32 tracks in the desired
sequence. If you like, store any track more
than once.
1 In the stop position, press PROG to activate
programming.
Display shows 1 indicating the start of
the program. prog flashes. (See 5)
2 Press ∞ or § to select your desired track
number.
3 Press PROG to store the desired track
number.
Display shows you desired track number
briefly followed by a number, 2 (up to
32 in sequence) indicating the next
program location available. (See 6)
4 Repeat steps 2 to 3 to select and store all
desired tracks in this way.
Fu indicates the program memory is full
(when you have stored tracks on all 32
program locations).
5 To play your program, press PLAY/PAUSE
2;.
CD Player
To review a program
•
In the stop position, press PROG repeatedly
to see your stored track numbers.
Erasing a program
You can erase the contents of the memory
by:
– selecting TUNER or TAPE/
POWER OFF
sound source;
– opening the CD door;
Display: prog disappears.
Cassette playback
1 Adjust the source selector to
TAPE/
.
POWER OFF
2 Press 9/ to open the cassette holder and
insert a cassette and close the deck.
3 Press 2 to start playback.
4 To pause playback press ;. To resume, press
the key again.
5 By pressing 5 or 6 , fast winding of the
tape is possible in both directions. To stop
fast winding, press 9/
6 To stop the tape, press 9/.
The keys are automatically released at the end
of a tape and the set switched off (unless
PAUSE mode ; has been activated.)
General information on recording
•
Recording is permissible insofar as copyright
or. other rights of third parties are not
infringed.
•
For recording, use only NORMAL type cas-
settes (IEC type I) on which the tabs have not
yet been broken.This deck is not suited for
recording on CHROME (IEC II) or METAL
(IEC IV) type cassettes.
Cassette Recorder
•
The best recording level is set automatically.
Altering the VOLUME will not affect the
recording.
•
To protect a tape from accidental erasure,
break out the tabs. If you wish to record again,
cover the tabs with a piece of adhesive tape.
Synchro Start CD recording
1 Select CD source.
2 Insert a CD and if desired, program track
numbers.
3 Press 9/ to open the cassette holder. Insert
a blank tape and close the deck.
4 Press 0 to start recording.
Playing of the CD program starts auto-
matically from the beginning of the pro-
gram. It is not necessary to start the CD
player separately.
5 For brief interruptions press ;. To resume
recording, press ; again.
6 To stop recording, press 9/.
Recording from the Radio
1 Adjust the source selector to TUNER to
select your desired waveband.
2 Tune to the desired radio station (see Tuner
reception).
3 Press 9/ to open the cassette holder. Insert
a blank tape and close the deck.
4 Press 0 to start recording.
5 For brief interruptions press ;. To resume
recording, press ; again.
6 To stop recording, press 9/.
Publicidad
Tabla de contenido
