Ryobi RHT2660R Manual De Utilización página 20

Deutsch (Übersetzung der originalen Anleitungen)
14. Latch
15. Safety tip
16. HedgeSweep™ debris sweeper
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
Make sure that all items listed in the packing list are included.
■
Inspect the product carefully to make sure no breakage or
■
damage occurred during shipping.
Do not discard the packing material until you have carefully
■
inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call Customer
■
Service for assistance.
PACKING LIST
Hedge Trimmer
Sheath
2-Cycle Engine Lubricant
Operator's Manual
WARNING
If any parts are missing do not operate this tool until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
WARNING
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading to
possible serious personal injury.
WARNING
To prevent accidental starting that could cause
serious personal injury, always disconnect the engine
spark plug wire from the spark plug when assembling
parts.
OPERATION
WARNING
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING
Always wear safety goggles or safety glasses with
side shields when operating power tools. Failure to do
so could result in objects being thrown into your eyes,
resulting in possible serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
MIXING THE FUEL (Fig. 2)
This product is powered by a 2-stroke engine and requires
■
pre-mixing petrol and 2-stroke lubricant. Pre-mix unleaded
petrol and 2-stroke engine lubricant in a clean container
English (Original instructions)
■
■
■
■
■
■
FILLING THE TANK
■
■
■
■
■
■
STARTING AND STOPPING (Fig. 3 )
The starting method differs depending on whether the engine
is cold or warm.
NOTE: Before starting the unit, make sure:
■ the On/Off switch is in "I" position;
■ the trimmer is lying on a flat and bare surface.
16
approved for petrol.
This engine is certified to operate on unleaded petrol
intended for automotive use with an octane rating
of 91 ([R + M] / 2) or higher.
Do not use any type of pre-mixed petrol / lubricant from
fuel service stations, this includes the pre-mixed petrol /
lubricant intended for use in mopeds, motorcycles, etc.
Use synthetic 2-stroke lubricant only. Do not use
automotive lubricant or 2-stroke outboard lubricant.
Mix 2% synthetic 2-stroke lubricant into the petrol. This is a
50:1 ratio.
Mix the fuel thoroughly and also each time before fueling.
Mix in small quantities. Do not mix quantities larger than
usable in a 30 day period. Synthetic 2-stroke lubricant
containing a fuel stabilizer is recommended.
Always refuel outdoors in a well ventilated area away from
sparks, flames and other ignition sources. Choose a hard
level surface for this task.
Clean surface around fuel cap to prevent contamination.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Clean and inspect the gasket.
Carefully pour fuel mixture into the tank. Avoid spillage.
Immediately replace fuel cap and hand tighten.
Wipe up any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine during and after first use.
WARNING
Always shut off engine before fueling. Never add fuel
to a machine with a running or hot engine. Move at
least 9 m from refueling site before starting engine.
Do not smoke!
1 Litre + 20 ml
2 Litres + 40 ml
3 Litres + 60 ml
4 Litres + 80 ml
5 Litres + 100 ml =
=
=
= 50:1 (2%)
=