Replacing The Filters - Minuteman KLEEN SWEEP 45 Modo De Empleo

SERVICE BRAKE.
The service brake is activated by releasing the forward/reverse speed
control pedal.
EMERGENCY BRAKE.
To stop the machine press the brake pedal (n°2 PIC.2).
PARKING BRAKE.
Press the brake pedal (n°2 PIC.2).
Pull the lever (n°3 PIC.2) and then release all.
To disconnect the parking brake slightly press the pedal (n°2 PIC.2)
and push the lever (n°3 PIC.2) back to its original position.
SAFETY DEVICES AND PARTS.
WARNING ! The safety parts and devices must not be tampered with.
They can be removed only when executing maintenance operations.
HOOD. The hood is a mobile part connected to the machine frame by
mean of hinges. It prevents access to moving parts. It is also an
acoustic and thermic insulator. The machine can not be operated when
the hood is raised.
HOOD SUPPORTING ROD. The hood supporting rod is a mechanical
safety device. When executing maintenance operations, fix the rod to
the hood to prevent it from falling.
TOTAL STOP KEY SWITCH. The total stop key switch is an electric
safety device. It cuts off all electric parts while the hood is open. To re-
activate the machine, close the hood and insert the key into the switch.
PERIODIC MAINTENANCE.
CHECK
Brush state. EVERY 10 HRS.
Filters state. EVERY 10 HRS.
Brake adjustment EVERY 100 HRS
Belt tension.
Side brush adjustment. EVERY 50 HRS.
Hydraulic oil. EVERY 50 HRS.
REPLACE
Filters. EVERY 300 HRS
Flaps
Brushes
IMPORTANT RULES TO BE FOLLOWED WHEN
SERVICING THE MACHINES.
• Before servicing the machine, disconnect the machine from its power
source:
Kleen Sweep 45 G: Disconnect the spark plug and the starting
battery clamp.
Kleen Sweep 45 E: Disconnect the connector (n°1 pic.6).

REPLACING THE FILTERS

Shake the filters (n°4 PIC.7) thoroughly.
Remove the nuts and washers (n°2 PIC.7).
Remove the filters holder/cover (n°3 PIC.7).
Change the filters (n°4 PIC.7), making sure the seals are in the
correct position, and the filter collar is correctly fitted inside the hole
in the sweeper frame.
Put the filters holder/cover back on and tighten it down, checking
that the filters are located in their seating.
Replace all the components removed, then tighten all screws.
ADJUSTING THE SIDE BRUSH
Adjust the screw (n°1 PIC.8).
HYDRAULIC TRANSMISSION OIL
Check the oil tank level every 50 hours of operation.
When topping up or when replacement of oil is necessary, you must
ask for advise from your nearest authorised service centre.
VIBRATIONS
The level of vibrations to which the operator is subjected is below the
maximum level allowed by the CE DIRECTORY for industrial machinery
( CEE 89\392 ).
TROUBLESHOOTING GUIDE
KLEEN SWEEP 45 G
PROBLEM
Battery flat. 1.Battery short-circuited.
2.Generator not
charging.
8
OPERATOR AUTHORISED
SERVICE CENTRE
* EVERY 200 HRS
* EVERY 300 HRS
* WHEN WORN OUT
CAUSE SOLUTION
1.Have it replaced.
2.Have it checked.
The engine won't
start although the
starter motor
operates correctly.
The engine smokes
and is nosier than
usual.
The engine wont
start and the motor
doesn't work.
KLEEN SWEEP 45
Shaker doesn't
work.
Battery won't
charge.
Everything stays off
when the key is
inserted.
BOTH VERSIONS
*
Dust inside the
*
engine bonnet.
*
The main brush
*
doesn't clean
*
uniformly and leaves
material on the floor.
*
The main brush
doesn't turn.
No suction when
moving.
Material and dust
comes out of the
front.
WARNING!
Any other type of service operation or test, with the exception of those
shown in the engine's manual or the battery's manual, must be carried out
by authorised personnel only.
WASTE MATERIAL.
FOR THE DUMPING OF WASTE MATERIAL SUCH AS OIL,
PLASTIC PARTS, BATTERIES, PACKING BOXES, PLEASE
CONTACT THOSE FACILITIES AUTHORISED FOR THE
DUMPING OF SPECIAL WASTE.
NOISE LEVEL
The level of noise has been measured to the level of the operator's ear
and while the machine is working .
• Kleen Sweep 45 G " BRIGGS & STRATTON ".
The maximum value read is 86 dB.
• Kleen Sweep 45 G " HONDA ".
The maximum value read is 86 dB.
• Kleen Sweep 45 E.
The maximum value read is 78 dB.
3.Accelerator down. 3.Pull up to 1/3.
4.Choke down. 4.Pull up to maximum.
5.Spark plug dirty. 5.Replace it.
6.Engine oil level very 6.Top up with oil.
low.
7.Carburettor out of 7.Get the carburettor
adjustment. setting adjusted.
8.Exhaust pipe broken. 8.Have it replaced.
9.Battery flat or faulty. 9.Recharge or have it
10.Starter motor faulty. replaced.
11.Contactor faulty. 10.Have it replaced.
12.Keyswitch faulty. 11.Have it replaced.
12.Have it replaced.
E
1.Vibrator motor faulty. 1.Have it replaced.
2.Fuse blown. 2.Have it replaced.
3.ON/OFF push-button 3.Have it replaced.
faulty.
4.Motors overloaded 4.Remove foreign or
because of extraneous change seized bearings
fragments causing .
friction between .
moving parts. 5.Recharge the battery,
5.Electrolyte density too have it replaced if
low. necessary.
6.Battery flat or faulty. 6.Recharge or replaced
7.Fuse blown. it.
7.Have it replaced.
1.Filters broken or worn 1.Replace it
out. 2.Fit the seals.
2.Seals not fitted under
filters.
3.Brush raised. 3.Lower it.
4.Brush worn out. 4.Adjust the lever or have
5.Not enough pressure on it replaced.
floor. 5.Increasing the spring
6.Material has load.
accumulated around 6.Have it replaced.
brush.
7.Belt broken 7.Have it replaced.
8. Belt loose. 8.Check belt tensioner.
9.Suction off. 9.Switch it on.
10.Filters clogged. 10.Shaker or replace them.
11.Flap seal worn or 11.Have it replaced.
broken. 12.Have it replaced.
12.Flap stuck.
.
.
.