Mirage NANOSAT PRESTIGE Serie Manual Del Propietário página 4

owners manual
7. When setting your subwoofer level, be sure that the setting on
your A/V Receiver or processor remains as close to flat as
possible. Boosting or cutting the subwoofer output on your A/V
Receiver or processor may produce poor sound quality. Instead,
use volume control on the back of the MIRAGE Subwoofer for
fine tuning.
You are now ready to enjoy your MIRAGE NANOSAT Prestige System.
NANOSAT PRESTIGE IN-DEPTH
INSTRUCTIONS
Stand Mount Options
This series provides a large choice of installation options to integrate
into any decor.
The bottom of the NANOSAT Prestige is designed to clip onto the
optional MS-STB-1 stand. Please refer to the MS-STB-1 owners'
manual for more detailed instructions.
Wall Mount Options
For wall mount installations, the NANOSAT Prestige is equipped with a
mounting bracket that can be used to mount the speaker securely to a
vertical surface. The bracket is shipped already attached to the speaker.
Carefully drive a #8 screw into a stud in the wall, leaving
approximately 1/4 inch of the screw exposed, then mount the
NANOSAT Prestige like you would a picture.
Note: Failure to attach the screw safely to a secure spot on the wall
can result is damage or injury. See Diagram 2
When mounting the speaker at a height of under six feet, orient the
NANOSAT Prestige in an upright position. Slide the head of the screw
into the wide portion of the channel opening and slide the NANOSAT
Prestige downward until it sits in position. See Diagrams 2 and 3.
When mounting the speaker at a height of over six feet, orient the
NANOSAT Prestige in an upside down position so the grill is facing the
floor and use the bottom key-way channel. Slide the head of the screw
into the wide portion of the channel opening and slide the NANOSAT
Prestige downward until it sits in position. See Diagrams 2 and 3.
The speaker can also be angled by slightly loosening the screw on the
bottom of the NANOSAT Prestige and swiveling the speaker into the
desired position.
NANO CC CENTER CHANNEL
1. Choose the desired mounting position. If possible, find a position
on the wall that allows the NANO CC to be mounted directly to a
wall stud. Attach the mounting template (included in the box) to
the desired position by using tape or small nails. See Diagram 6.
IMPORTANT: The arrows on the template should point in the same
direction as the grill. If the NANO CC is mounted below 6 feet, the
grille should face upwards and therefore the arrows on the template
should also point upwards. If the NANO CC is mounted above 6
feet, the grille should face downwards, and similarly the arrows on
the template should also point downwards.
2. Using a level, ensure the template is attached level to the wall. It
is critical that the template is level as a mistake at this stage will
result in uneven mounting of the NANO CC. See Diagram 7.
3. Outline the two rectangular boxes. Mark the smaller box with an
X. The smaller box is needed for the wire management outlining
the recommended wall cut-out. See Diagram 8.
4. After the template has been removed, use a drywall saw to cut
out the smaller rectangular box marked with an X. Please note
that this step is only required if the wires will be fed through the
wall. If a different wire management system is being used, please
ignore this step. See Diagram 9.
5. Mount the wall bracket into position. The use of proper anchors
for all screws is required to ensure a secure installation. Please
note that screws and anchors are not included in the NANO CC
package. See Diagram 10.
6. Feed the wires through the hole cut out. See Diagram 11.
7. Connect the wires to the appropriate binding posts at the back of
the NANO CC.
IMPORTANT: Connect the speaker wire from the positive (RED +)
terminal on the amplifier to the positive (RED+) terminal on the
speaker. Connect the negative (BLACK-) terminal on the amplifier to
the negative (BLACK-) terminal on the speaker.
8. After the wires are connected, hang the NANO CC on the wall
bracket. Center the NANO CC and push down lightly on the
speaker to achieve a tight fit between the speaker and the
bracket. If the speaker is not centered, repeat this step. See
Diagram 12.
4