Tabla De Contenido; Safety Instructions - Emerson LED PRO Serie Manual Del Usuario

Section
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1. Unpacking Instructions
2. Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .4
3. Removal of the Hanger Bracket . . . . . . . . . . . . . . . . . . . .5
4. Installing the Hanger Ball/Downrod Assembly
5. Installing the Ceiling Cover on the Fan Motor Housing
. . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
(Close-to-Ceiling)
6. How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . .10-11
7. Hanging the Ceiling Fan
8. Hanging the Ceiling Fan
9. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . .13-14
10. Installing the Ceiling Cover . . . . . . . . . . . . . . . . . . . . . .15
READ AND SAVE THESE INSTRUCTIONS
WARNING
!
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS,
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
1. Read your owner's manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code "ANSI/NFPA 70-2017" and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
Table of Contents
. . . . . . . . . . . . . . . . . . . . . . . . .3-4
(Standard)
. . . . . . . . . . . . . . . .11
(Standard)
. . . . . . . . . . . .12
(Close-to-Ceiling)

Safety Instructions

OBSERVE
Page Section
11. Installing the Fan Blades . . . . . . . . . . . . . . . . . . . . . . . .16
12. Installing the Light Fitter . . . . . . . . . . . . . . . . . . . . . .17-21
13. Using Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . .22
14. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
6-7 15. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
16. Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . .23
17. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-25
18. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . .27
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as "Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less", and use the
THE
mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed
controls.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson could result in personal injury or property
damage.
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
2
WARNING
!
U.L. Model No.: 52-ANT
Page