Pelonis FS45-9L El Manual Del Propietario página 4

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ASSEMBLY INSTRUCTIONS
Step 1. Fan Base Assembly (Fig. 1)
1. Unscrew the Screw (U) from the external Pole (P) and attach the external Pole (P) to the Base (T) by tightening
the Screw(U).
2. Remove the height adjustment Knob (O) by unscrewing it counterclockwise.
3. Use your finger to pull out the internal Pole(N), slide height adjustment Knob (O) over internal Pole (N). Fasten
it to external Pole (P) by turning the knob while holding the pole. Make sure the Knob (O) is tightly fastened.
Step 2. Fan Head Assembly (Fig. 2)
1. Remove the blade Cap (B) by turning clockwise. Remove the plastic Nut (D) by turning counter clockwise.
2. Position the rear Grille(E) over the motor Shaft(F), make certain the handle is at the top and the one notch in the
rear of rear Grille(E) cover fit over the three prong on the motor Housing(H).
3. Secure rear Grille(E) by turning the plastic Nut(D) clockwise and tightening firmly.
4. Slide the fan Blade(C), with the hollow interior of the blade facing toward rear Grille(E), onto motor Shaft(F).
5. Secure Fan Blade(C) onto motor Shaft(F) by turning the blade Cap (B)counterclockwise until it firmly in place.
6. Loosen the bolt on the bottom of the Front Grille(A) and mount the Front Grille(A) with the logo right side up to the
Rear Grille ( E ) by snapping both together firmly.Ensure all snaps around the Front Grille(A) are secure on the
Rear Grille (E).
7. Tighten the bolt on the bottom of the Front Grille( A).
Step 3. Final Assembly (Fig. 4)
1. Loosen the thumb Screw (J) by turning it counter clockwise.
2. Always keep the water proof Cover(L) match with the height adjustable Knob (O)when adjusting the internal
Pole(N).
3. Insert internal Pole(N) into the neck joint and tighten by turning thumb Screw(J) clockwise. Make sure it is tight
enough to support the fan head.
4.Attach the Misting Line Holder(M) onto the Internal Pole(N).
5.Secure the Misting Line(Q) to the clip under the Front Grille(A) and the Misting Line Holder(M).
Fasten
O
N
P
OPERATING INSTRUCTION
1. Place the fan on a level surface. Plug the grounding type attachment plug into a standard 120V AC
3-Prong wall outlet.
2. Attach the Valve(S) onto a standard outdoor hose. Turn your water on at the spigot and use the lever on the
Valve(S) to turn water on and off.
3. To turn oscillation mode on, push the Clutch Knob (G). Pull the Clutch Knob (G) up to turn oscillation off.
4. To adjust the air flow upward or downward, simply tilt the fan head with hand and move to desired angle.
5. Control speed by pushing the desired button :
0 - OFF, 1 - low, 2 - medium, 3 - high
6. The height of the fan can be adjusted by loosening the height adjustment Knob (O) and carefully adjusting the
Internal Pole(N). the fan and retightening Height adjustment Knob(O). Always ensure the waterproof Cover(L)
covers the Height adjustable Knob(O) after adjusting the Internal Pole(N).
B
D E
F
T
A
C
U
Fig. 1
Fig. 2
Q
Fig. 3
3
J
L
N
M
O
Fig. 4

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

758415

Tabla de contenido