Publicidad
V I D E O P O R T E R O E L E C T R Ó N I C O - V I D E O D O O R E N T R Y S Y S T E M S - V I D É O P O R T I E R É L E C T R O N I Q U E
VERIFICACIÓN DE LA INSTALACIÓN
No funciona nada.
Introduciendo un código correcto, no funciona el abrepuertas
principal.
Introduciendo un código correcto, no funciona el abrepuertas 2
TROUBLESHOOTING
Ensure that the entrance panel emits a beep approximately 5
seconds after you press any key. If the key pressed is the one
marked
the entrance panel will emit one beep when the
key is pressed and another after approximately 15 seconds.
If you cannot access the user menu, make sure that in position
5 of the installation menu you have entered 1.
Nothing works.
Check the mains voltage in the power supply unit. Check
that the output voltage of the power supply unit is within its
operating range. Check if there is any short circuit, and if
so, repair it. Disconnect the power supply unit from the
mains for one minute, then reconnect it. If the problem
persists, disconnect all the output terminals from the power
supply unit and check the output voltage. If it is not correct,
the power supply unit may be defective.
A correct code has been entered but the main electric lock does
not work.
Ensure that when entering the correct door-opening code,
the green led lights up and that the entrance panel emits 3
beeps. If they do, while the green led is lit up, check the
voltage between terminals 11 and 12. If the voltage is
correct, check the connections between terminals 11 and
12 and the electric lock. If necessary, replace the electric
lock. Check the voltage of terminals 11 and 12c. If there is
no standby voltage, check the bridge between
If no fault is discovered, the equipment may be defective.
A correct code has been entered but the electric lock 2 does
not work.
Disconnect the electric lock 2. Make sure that when the
correct code of the secondary relay is entered, the green
led lights up and the entrance panel emits 3 beeps. If they
do, while the green led is lit up, check for continuity between
terminal C1 and NO1. If there is continuity, check the
connections between terminals C1 and NO1, the additional
Introduciendo un código correcto, no funciona el relé auxiliar.
Con un pulsador exterior no funciona alguno de los relés.
Introduciendo el código maestro correcto, no se puede acceder
al menú de instalación.
0
power supply unit and the electric lock 2. If necessary,
replace the electric lock 2.
Check for continuity between the terminals C1 and NC1.
If there is no continuity in standby, or if there is continuity
which persists even though the secondary relay is active,
the equipment may be defective.
A correct code has been entered but the auxiliary relay does
not work.
Disconnect the accessory connected to this relay. Press any
key and check for continuity between terminals C2 and
NO2. If there is continuity, check the connections between
terminals C2, NO2, the extra power supply unit and the
accessory. If necessary, replace the accessory.
Check terminals C2 and NC2 for continuity. If there is no
continuity in standby, or if there is continuity which persists
even though the auxiliary relay is active, the equipment
may be defective.
Some of the relays don't work when pushing an external
pushbutton.
Check the voltage or continuity of the contacts when a
bridge is made between terminal – and terminals 22, Ctrl1
or Ctrl2. If no fault is detected, the equipment may be
defective.
The correct master code has been entered but it is impossible
to access the installation menu.
and .
Ensure that the voltage of the equipment’s power supply is
correct. Check that when the keys
pressed, the red led blinks. If it does, enter the MASTER
code. If the red led does not blink, the equipment may be
defective.
0
–
0
0
,
,
,
are
Publicidad
