Multiplex FunJet Instrucciones página 4

!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
The "FunJET" high-performance power set, # 33 2630, is
designed for fast model jets weighing up to 800 g, such
as our FunJET. For brisk flying we recommend the use of
a 2S LiPo battery (Standard). If you like things to move
more quickly, we recommend a 3S LiPo pack (Fun).
2. C / R
ONTENTS EPLACEMENT PARTS
• 1 Himax A 2825-2700
• 1 MULTIcont BL-37/II speed controller
• 1 5.5" x 4.5" propeller
• 1 propeller driver
•
Various small items for installation in the model
3. T . O
YP PERATIONAL
P S "F
OWER ET UN
2S LiPo / 5.5" x 4.5" prop
3S LiPo / 5.5" x 4.5" prop
Recommended flight battery:
Standard:
MULTIPLEX Li-BATT BX 2/2500
MULTIPLEX Li-BATT BX 2/3200
Fun:
MULTIPLEX Li-BATT BX 3/2500
MULTIPLEX Li-BATT BX 3/3200
Do not use the supplied Himax A 2825-2700 motor with
more than 3S LiPo or 9 NiXX cells when using the
recommended propellers.
4. S N
AFETY OTES
The power set "FunJET" is designed exclusively for use in
modelling applications. Incorrect use can result in serious
personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the
propeller blades
• Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions for Power Set "FunJET"
# 33 3040
# 7 2276
# 73 3141
# 33 2308
D
ATA OF
JET"
Current drain: approx. 15.0 A
Current drain: approx. 30.0 A
# 15 7190
# 15 7135
# 15 7191
# 15 7136
5. A O
SSEMBLING
P S "F
OWER ET
1. Screw the motor to the motor mount.
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propeller on the propeller driver, and secure
them with the spinner (supplied).
6. I
NITIATION OF THE
P S "F
OWER ET
1. Connect the three wires attached to the speed
controller to the three wires attached to the motor; the
order of connection is unimportant.
2. Locate the UNI connector attached to the speed
controller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the "OFF" position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking
forward. If this is not the case, disconnect the flight
battery and swap over any two of the three motor wires.
6. Switch off the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
T
F HE
JET"
UN
JET"
UN
Page 1/2