Safety Instructions - Flex LD 24-6 180 Manual De Instrucciones

Safety instructions

t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=áå=
~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
 This electric power tool must be used as
a sander. Observe all safety information,
instructions, diagrams and data which
you receive with the power tool.
If you do not observe the following
instructions, an electric shock, fire and/or
serious injuries may occur.
 This electric power tool is not suitable for
use with sandpaper, wire brushes, or for
polishing and cut-off grinding.
If the electric power tool is not used as
intended, the user may be exposed to
hazards and may be injured.
 Never use accessories which the
manufacturer did not intend or
recommend especially for this electric
power tool.
Just because you can attach the accessory to
your electric power tool does not guarantee
safe use.
 The permitted speed of the insertion tool
must be at least as high as the maximum
speed indicated on the electric power
tool.
An accessory which rotates faster than
permitted may shatter and fly off.
 Outer diameter and thickness of the
insertion tool must correspond to the
dimensions of the electric power tool.
Incorrectly measured insertion tools cannot
be adequately shielded or controlled.
14
 Sanding discs, sanding pads or other
accessories must fit exactly on the
grinding spindle of your electric power
tool.
Insertion tools, which do not fit exactly on the
grinding spindle of the electric power tool,
rotate unevenly, vibrate violently and may
result in loss of control.
 Do not use any damaged insertion tools.
Before use, always check insertion tools
for splinters and cracks, sanding pad for
cracks, wear and severe abrasion. If the
electric power tool or the insertion tool is
dropped, check for damage or use an
undamaged insertion tool. When you
have checked and inserted the tool,
ensure that you and anybody in the
vicinity remain outside the plane of the
rotating insertion tool and leave the
power tool running for one minute at
maximum speed.
Damaged insertion tools usually break during
this test time.
 Wear personal protective equipment.
Depending on the application, wear full
face protection, eye protection or
goggles. If appropriate, wear a dust
mask, hearing protection, protective
gloves and/or a special apron which
protect you from small sanding and
material particles.
You should protect your eyes from foreign
objects which are ejected for different
applications. Dust and respirator masks must
filter the dust which is generated by the power
tool for the particular application. If you are
exposed to loud noise for a prolonged period,
you may suffer hearing loss.
 Ensure that other persons are situated
at a safe distance from the work area.
Anyone who enters the work area must
wear personal protective equipment.
Fragments of the workpiece or broken
insertion tools may fly off and cause injuries
even outside the direct working area.
LD 24-6 180