Carrera DIGITAL 124 Instrucciones De Uso Y Montaje página 9

1 2 3
Connections (from left to right):
Connection for Lap Counter 20030342
1
Connection for PC-unit or Lap Counter 20030355
2
or App Connect 20030369
Connector 1 for speed controller, speed controller extension set
3
or WIRELESS+ receiver
Connector 2 for WIRELESS Tower 20010108
4
5 Connector 3 for speed controller
Connector 4 for speed controller
6
Connection for DIGITAL 124 / DIGITAL 132 power supply
7
General information on connectors 1-4:
When a WIRELESS+ receiver is used, it must be plugged into con-
nector 1. Optionally a Wireless Tower 20010108 can be plugged into
connector 2. When only the WIRELESS+ receiver is used, connec-
tor 2 is to be left empty.
4
5
On/off switch
1
Switch for fuelling function
2
Button to start the race / acknowledge programming
3
Button for Pace Car / termination of programming
4
Button for setting basic speed
5
Button for setting braking performance
6
Button for setting fuel tank capacity
7
Programming button for cars
8
Encoding/programming
of cars to the according
speed controllers
2 1
4
1 2
7 1x 8
5
3 4
To encode a car place it on the track and swich on the Control Unit.
Press "Code" button once 8 , fi g. ; the fi rst LED starts to light,
1
fi g. . Then push lane-change-button once on the relevant speed
2
controller, fi g. . In case the car is equipped with lights they will
3
start to fl ash and the Control Unit´s LEDs 2-4 will light successively.
Once encoding has been carried out the middle LED lights perma-
nently (fi g. 4 ) and the car is allocated to the speed controller.
Note: This kind of encoding requires to only have the car on the
racetrack which shall be encoded.
Connections
4
Additional wired speed controllers may be plugged into connectors
3 and 4. Please note that these will use address 5 and 6 then.
Using the speed controller extension set 20030348 it has to be
plugged into connector 1. The cars´ addresses will be allocated as
follows:
• Speed controller extension set = address 1, 3 and 4
• connector 2 = address 2
• connector 3 = address 5
• connector 4 = address 6
Note:
a combination of WIRELESS and speed controller extension set is
not possible!
Control elements
3 2
6 7
General operating information
Some buttons are assigned with diff erent tasks. In order to set a
function you need to use key combinations. Any programming steps
can be cancelled with button
further details in the course of this manual.
Encoding/programming
3 2
1
2x
6 7
3
5
100
50
0
Switch on the Control Unit, place the car to be encoded on the track
and press „Code"
trol Unit start to light, fi g.
the speed controller, fi g.
until the middle LED lights again, fi g.
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, fi g.
Autonomous Car´s encoding is completed now.
5 6 7
4 3
5 6
1
8
4 "ESC/PACE CAR". You will fi nd
of Autonomous Car
1
2
8
4
4
5
4
150
SPEED
200
+
CLICK
250
5
300
8 twice, fi g. . The fi rst two LEDs at the Con-
1
. Now push the lane-change button at
2
; LEDs 3-5 will light successively. Wait
3
. Activate the speed
4
.
5
Note: This kind of encoding requires having only the car on the
track which is to be encoded. The programming of the Autono-
mous Car will be maintained unless the car is not being recoded.
The Autonomous Car is always displayed with address 7 in combi-
nation with the Position Tower.
Encoding/programming
Pace Car
Pit Lane 20030356
2 1
1 2
3x
7 8
3 4
5
150
SPEED
100 200
+
CLICK
50 250
0 300
(only in combination with Pit Stop Lane #20030356)
Switch on the Control Unit, place the car to be encoded on the track
and press "Code" 8 three times, fi g.
the Control Unit start to light, fi g. . Now push the lane-change but-
2
ton at the speed controller, fi g. ; LEDs 2-5 will light successively.
3
Wait until the middle LED lights again, fi g.
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, fi g. . The Pace Car´s encoding is
5
completed now and the car enters the Pit Stop Lane.
Note: This kind of encoding requires having only the car on the
track which is to be encoded. The programming of the Pace Car
will be maintained unless the car is not being recoded. The Pace
Car is always displayed with address 8 in combination with the Posi-
tion Tower.
Extended Pace Car function
After the Pace Car´s encoding has been completed it will auto-
matically enter the Pit Lane during the fi rst laps. In order to start the
Pace Car please push the button "Pace Car"
2 and 3 at the Control Unit will light and the Pace Car will leave the
Pit Lane. The Pace Car will now drive as long as the button „Pace
Car" is pushed again. LED 2 stops lighting and the car automatically
enters the Pit Lane within the current lap.
Display of position
Autonomous and Pace Car
1
Position
Tower
3 2
20030357
4
2 3
6 7
3 2
5 6 7
(only in combination with Position Tower #20030357)
The position of the Autonomous Car (address 7) and of the Pace
6 7
Car (address 8) can be displayed at the Position Tower. This func-
tion can be activated at the Control Unit. Therefore switch off the
Control Unit and keep the "BRAKE" button
switch on the racetrack and release the "BRAKE" button again. By
pushing the button again the function may be changed:
1 LED lights = no display
2 LEDs light = display at the Position Tower
Set the function requested and confi rm your choice via "START/
ENTER".
. The fi rst three LEDs at
1
. Activate the speed
4
4 once. The LEDs
1
2 1
8
1
8
8
6 pushed, fi g. ,
2
9