Installation
8. Swing the gate into the closed position and slide the gate panels until the gate contacts
Fig. 4
the latch side of the mounting surface (Fig. 4).
E
9. Making sure that the top of the gate is level with the floor, using a pencil
mark the position for the holes for the latch housing
10. Swing the gate out of the way, and remove the latch housing.
11. Drill holes as in Step 4. Using the correct screws (see Step 5), secure the upper latch
Fig. 5
housing to the mounting surface.
D
12. Slide the lower latch housing over the lower gate rail.
13. Using a pencil, carefully mark the position for the holes of the lower latch housing.
14. Open and swing the gate out of the way. Remove the lower latch housing from the rail.
15. Drill holes as in Step 4. Using the correct screws (see Step 5), secure the lower latch
housing to the mounting surface.
16. To close gate, place the lower rail into the lower latch housing, while squeezing
C
the latch
C
, insert it into the upper latch housing
17. Test the gate mounting by firmly shaking the top rail of gate.
18. To open the gate, squeeze the latch and slide the gate open.
19. To install optional swing control mechanism, see below.
20. Always keep the latching mechanism securely engaged when using the gate.
21. Remove the gate from opening when not in use.
Optional Swing Control
A
#10 x 1/2" Screws
B
D
.
D
(Fig. 5).
The optional swing control mechanism provides extra security.
We recommend the swing control mechanism be used to prevent
the gate from swinging into a hazard such as over stairs or into a
heavy traffic area.
1. Mount the gate according to instructions.
2. Determine the direction you want to prevent the gate from
swinging into.
3. Attach the swing stop
A
to the top rail
B
with the solid surface
of the swing stop toward the direction of the hazard, i.e. the
direction you want to prevent the gate from swinging into.
4. The optional swing control mechanism should not be used in
place of the latching mechanisms.
Always keep the latching mechanism securely engaged when
using the gate. Remove the gate from opening when not in use.
2
• Wash gate with mild soap and warm water and dry thoroughly before using.
• Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth. DO NOT use abrasive cleaners
, carefully
E
or solvents.
• An occasional drop of vegetable oil may reduce wear and tear on moving parts.
For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user ("Purchaser") this
Product (including any accessories) against defects in material or workmanship. Evenflo's sole obligation under this express lim-
ited warranty shall be, at Evenflo's option, to repair or replace any Product that is determined to be defective by Evenflo and
determined to be covered by this warranty.
Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase in the form
of a receipted invoice or bill of sale evidencing that the Product is within the warranty period must be presented to obtain
warranty service. This express limited warranty is extended by Evenflo ONLY to the original Purchaser of the Product and is
not assignable or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo's
ParentLink Consumer Resource Center at (800) 233- 5921 or www.evenflo.com.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON THIS
PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW. OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH
ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER
EXPRESS REPRESENTATION OF ANY KIND IS HEREBY DISCLAIMED.
Care and Maintenance
Limited Warranty
A
3