Tool Change - stayer HP750BE Manual De Instrucciones

hold the switch. These models also have an engine
lock button that allows you to keep the engine running
without having to keep the switch pressed.
In the LP1000E model, if you quickly press twice
in succession, you can enter protection due to the
unintentional start of the machine. In these conditions
the machine will stop and you will have to wait a few
seconds for safety before restarting them. To start
correctly, always keep the power switch pressed.
To switch OFF:
For the LP 700 E model, stop pressing the switch.
For LP710E, LP710DT models press the switch to lea-
ve it in the "off" / OFF position.
For HP750BE, HP1010, LP1000 BRUSHLESS mo-
dels stop pressing the switch. In case of having the
motor locked in constant operation, lightly press the
switch again to stop the machine.

TOOL CHANGE

Change of the disk
The abrasive disk can be easily changed thanks to the
fabric adhesion system. Just pull the disc and replace
it with a new one.
NOTE: Only use sandpaper discs which fit properly
and which are designad far vacuum use.
Change of brush ring
The brush bristles on the edge of the sanding
plata cover serve two purposes, they keep the
sanding disc properly aligned with the work surface
without gouging and they also help the efficiency
of the dust collection by the vacuum cleaner.
These brush bristles will wear with continuad use.
The sanding plata cover should be replaced when the
bristles are too worn to ensure effective dust collection
and stabilization of the sanding head.
Replacement is the opposite of removal. Entrust all
repairs to an authorized service centre.
Remove the brush ring by removing the 6 or 8-star
screws.
Sanding pad change
- Insert a hex key into the center screw with hex nut on
the sanding pad.
- Insert a rod, allen key or screwdriver in one of the
suction holes to immobilize the plate, holding the tool
with your hand.
- Turn the hex key to remove the chainring.
- Install the new sanding by tightening the central
screw.
Speed setting
The speed of the machine varies to suit different tasks
using the wheel. The highest speed should be used for
a fast, coarse sanding and the lowest speed for more
precise control and a finer finish.
5_INSTRUCTIONS OF USE
Effective control of this powerful tool requires two-
handed tor maximum safety and control.
Always wear respiratory mask and glasses with EPI
level.
Once the machi ne and vacuum cleaner are set up
and all safety measures and equipment are in place,
begin by turning on the vacuum cleaner and then the
machine. (lf you are using a vacuum cleaner with
integrated switching, then simply turn the machine on.)
Begin sanding and carefully contact the work surface
as lightly as possible-just enough to keep the sanding
head flat against the surface.
The joist in the sanding head allows the sanding disc
to follow the contours of the work surface.
The best technique is to use overlapping sweeps and
keep the head in constant motion. Never stop too long
in any one place ar there will be swirl marks. With
experience it will be very easy to create excellent
results.
For a better job in the joints between walls and / or
ceilings in the LP1000E model, a part of the brush ring
can be removed to gain access to the 100% joint. To
remove, release the tab on the top of the sanding head
to remove the part.
NOTE: Ensure that the sandpaper you are using
is suited to the task, overly coarse grit paper may
remove material too quickly to control. While overly
fine grit paper may clog too often and not shape down
the surface.
CAUTION: Take care to avoid sharp projections
and nails, etc.This will wipe out the sandpaper and
probably damage the sponge pad as well.
ELIMINATION
We recommend that the power tools, accessories and
packaging should be a recovery process that respects
the environment.
Only for EU countries:
Do not dispose of power tools into hou-
sehold waste!
According
2012/19/UE on Waste Electrical and Electronic
Equipment and its implementation into national law,
must accumulate separately far power tools under an
ecological recycling.
Subject to modification.
- 11 -
to the European Directiva
es
it
gb
fr
p
pl
cz
el