EINHELL GC-ET 4526 Manual De Instrucciones página 17

CAUTION! The guard is vital for your
safety and for the safety of others, and it is
also essential for the grass trimmer to work
correctly. Failure to observe this instruction
will not only create a potential hazard, it will
also result in the loss of your rights under
the warranty.
•
Never try to stop the cutter (nylon line) with
your hands. Wait until it stops by itself.
•
It is imperative to use only the original nylon
line. Never use metal wire instead of the nylon
line.
•
Beware of injuring yourself on the line cutting
device.
•
Keep the air vents clear of dirt.
•
After use, unplug the machine and check it for
damage.
•
Never attempt to cut grass that is not growing
on the ground. For example, do not try to cut
grass growing on walls, rocks, etc.
•
Within the working radius of the grass trim-
mer the user is responsible for any damage
caused to third persons by use of the trimmer.
•
Never cross roads or pebble paths with the
grass trimmer switched on.
•
When you are not using the grass trimmer,
keep it in a dry place out of the reach of child-
ren.
•
Use the grass trimmer only as described in
these directions for use and always hold it
vertical to the ground. All other positions are
dangerous.
•
Check the screws regularly to see that they
are properly tightened.
•
The mains voltage must be the same as the
voltage specified on the rating plate.
•
Check the power cable regularly for signs of
damage or aging. Never use the grass trim-
mer if the power cable is in less than perfect
condition.
•
Power cables used with the trimmer must not
be of a lighter duty class than HO7RN-F rub-
ber-insulated flexible cables according to DIN
57282 / VDE 0282 with a minimum diameter
of 1.5 mm2. Plug connectors must be equip-
ped with earthing contacts and the coupling
must be rain-water-protected.
•
If the cable is damaged during operation, dis-
connect it immediately from the power supply.
DO NOT TOUCH THE CABLE BEFORE IT
IS DISCONNECTED FROM THE POWER
SUPPLY.
•
To prevent danger, damaged power cables
Anl_SA_GC_ET_4526_SPK8.indb 17 Anl_SA_GC_ET_4526_SPK8.indb 17
GB
must be replaced by the manufacturer or by a
service company authorized by the manufac-
turer to carry out the work.
•
The equipment may only be powered via an
earth-leakage circuit breaker (RCD) with a
maximum operating current of 30 mA.
•
Keep cables and other objects out of the area
you want to cut.
•
If you have to lift the grass trimmer to move it,
switch off the motor and wait for the rotating
tool to stop. Before you leave the trimmer,
switch off the motor and pull out the power
plug.
•
Before you connect the grass trimmer to the
power supply, make sure that none of its
moving parts are damaged and that the line
spool is correctly inserted and fastened.
•
Never cut against hard objects when using
the grass trimmer. This is imperative to avoid
causing injury to the user and damage to the
trimmer.
•
Use only original replacement parts for repair
and maintenance purposes.
•
Have repairs carried out only by a qualified
electrician.
•
Examine the grass trimmer for signs of wear
or damage each time before you use it and
after any collisions. Have essential repairs
carried out without delay.
•
Always keep your hands and feet away from
the cutting mechanism, particularly when you
switch on the trimmer.
•
After pulling out new line, always return the
trimmer to normal working position before you
switch it on again.
•
Never use replacement parts or accessories
which are not foreseen or recommended by
the manufacturer.
•
Pull out the power plug before carrying out
any inspection, cleaning or other work on the
trimmer and whenever it is not being used.
•
Use the equipment only in broad daylight or in
well-lit conditions.
•
Keep the extension cable away from cutting
tools at all times.
Important: The nylon line continues to
rotate for a few seconds after the motor is
switched off .
The equipment does not start.
- 17 -
18.04.16 09:58 18.04.16 09:58