Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING: This pump is designed for use with DEF (AdBlue), Urea, Low Viscosity Non-Oil
and Non-Petroleum based Fluids, Anti-Freeze, Soap Solutions, Water and Water-based Mild
Chemicals only. Not suitable for use with Oil or Petroleum-based products such as Kerosene,
Diesel, Gasoline, etc. Always Pump in a well ventilated area. Never Smoke near any fluids
that are to be pumped. Follow the Safety Tips in this Manual. Refer to the materials below, to
check which Fluids can be pumped, using this Pump.
WETTED MATERIALS: Thermoplastic Polyurethane (TPU); Polypropylene (PP); Nylon/Polyamide (NYL); Nitrile
Rubber (Buna-N/NBR); Viton
Materials (Can be Pumped): Anti Freeze (Alcohol & Glycol Base); Detergent Solutions; Fruit Juices; Salt Water
(Brine); Sea Water (Brine); Soap Solutions; Urea/DEF/AdBlue; Vegetable Juices; Water: Fresh and Distilled
(Deionized) and Wines.
Warning: This product is not intended for potable water applications (human consumption – drinking and
cooking) and has not been designed to be compliant with the "Safe Drinking Water Act" requirements for low
lead in potable water applications. This item is for use only in non-potable (non-human consumption) water
applications.
Materials (Should Not be Pumped): Actaldehyde; Acetic Acid (20-50%); Acetic Anhydride; Acetone; Alcohols
(Amyl, Benzyl, Butyl, Diacetone, Ethyl (Ethanol), Hexyl (1-Hexanol), Isobutyl, Isopropyl, Methyl (Methanol), Propyl,
Aluminum Sulfate; Ammonia (Anhydrous, Liquid); Ammonium Hydroxide; Benzene; Benzoic Acid; Bleach
Solutions, Boric Acid (30%); Brake Fluid (Hexylene Glycol); Calcium Carbonate; Calcium Chloride; Calcium
Hypochlorite (20%); Calcium Sulfate; Chlorine (Wet); Chlorox; Citric Acid; Copper Chloride; Copper Sulfate; Diesel
Oil (Fuel ASTM #2); Ethyl Acetate; Ethylene Glycol; Formaldehyde; Formic Acid; Fuel Oils (ASTM #1-#9); Gasoline
(Unleaded); Gasoline (Petrol); Glycerol (Glycerine); Grease; Heptane (Brake Cleaner); Hexane; Hexyl Alcohol
(Hexanol); Hexylene Glycol (Brake Fluid); Hydraulic Oil; Hydrochloric Acid (20%-30%); Hydrogen Peroxide (30%);
Isobutyl Alcohol; Isopropyl Alcohol; Jet Fuels (JP1 to JP6); Kerosene; Lacquers; Lacquer Solvents; Lactic Acid;
Lubricating Oils (Petroleum); Methyl Ethyl Ketone; Mineral Oil (Petroleum); Motor Oil; Naphtha; Nitric Acid (50%);
Oils (Animal, Mineral, Vegetable); Oxalic Acid; Petroleum (Crude Oil); Phosphoric Acid (50%); Photographic
Developer; Potassium Chloride; Potassium Hydroxide (Caustic Potash); Propylene Glycol; Silicone Oils; Soda
Ash (Sodium Carbonate); Sodium Bicarbonate; Sodium Chlorate; Sodium Chloride; Sodium Chromate; Sodium
Hydroxide (50%); Sodium Hypochlorite; Sodium Nitrate; Sodium Nitrite; Sodium Peroxide; Sodium Phosphate;
Sodium Silicates; Sodium Sulfate; Sodium Sulfide; Sodium Sulfite; Stearic Acid; Stoddard Solvent; Sulfuric Acid
(75%); Tallow; Toluene; Toluol; Transformer Oil; Transmission Fluid (Type A); Trichlorethane; Trichlorethylene;
Turpentine; Varnish; Vegetable Oils; Vinegar; Xylene; Zinc Chloride and Zinc Sulfate.
Caution: The above Materials List is to be referred for guidance only in selecting equipment for appropriate
chemical compatibility. ALWAYS test your equipment under the specific conditions of your application before
permanent installation. Ratings of chemical behavior listed in this manual apply at a 48 hour exposure period.
Lumax has no knowledge of possible effects beyond this period. All recommendations are based on room
temperature (72°F/22°C) exposure. Compatibility results may deviate from these recommendations at elevated
temperatures. Recommendations are based on presence of listed chemical only. Mixtures containing more
than one chemical can greatly affect chemical compatibility. Polypropylene products and components should
not be used with low flash point chemicals, regardless of chemical compatibility results. Failure, improper
selection, or improper use of the products referred to and described herein or related items can cause severe
personal injury or property damage. This document and other information provides product options for further
investigation by users having technical expertise. It is important that you analyze all aspects of your application
and review the information concerning the product or system.
Due to the variety of operating conditions and applications for these products, the user, through his or her
own analysis and testing, is solely responsible for making the final selection of the products and assuring that
all performance, safety and warning requirements are met. The materials described and referred to herein
are subject to change at any time without notice. Lumax does not warrant (neither express nor implied) that
the information in this chart is accurate or complete or that any material is suitable for any purpose. If there is
any question about any Material that can or cannot be pumped, do not operate the pump. Check with Lumax
as to whether it is safe or unsafe, to operate the pump.
2
®
(Fluoropolymer Elastomer); Stainless Steel (SS 304)
Publicidad
